4mm Insulating Lining Paper Graphite Plus is an ultimate product that utilizes the natural reflectivity of graphite combined with polystyrene cells to create an effective energy saving insulating wallcovering.

Made from a 4mm thick layer of BASF EPS, infused with graphite particles and laminated to a reinforced backing, Graphite+ delivers 20% better insulation performance than standard Insulating Lining Paper.

This is equivalent to having an extra 26cm of concrete on your walls over and above an insulating lining paper.

Graphite+ Lining Paper is treated with a fire retardant additive and has been approved by the Energy Saving Trust due to its thermal efficiency and energy saving properties.

The special graphite particles act like thousands of mirrors reflecting radiant heat back into the room and thus reducing heat loss and energy bills.

Graphite+ is a paste the wall product which makes it easier to use.

Furthermore the product is extremely effective in disguising uneven and defective wall surfaces.

Specification:

Thickness: 4mm

Roll Width: 500mm

Roll Length: 7500mm

Roll Coverage: 3.75m²

Material: BASF Graphite Polystyrene

Applications: Interior

4mm Insulating Lining Paper Graphite Plus Features:

 · Value 0.125 m²K/W.

 · U Value 8 W/m²K.

 · Laminated Polystyrene with graphite components to increase heat saving properties.

 · Graphite components increase material stability and strength.

 · Resists damp and mould formation on problem walls.

 · Twice as thick as regular polystyrene wall veneers.

 · For quick and effective insulation of inside walls.

 · Supplied ready laminated to a reinforced liner

 · Reduces external noise pollution.

 · CFC free.

4mm Insulating Lining Paper Graphite Plus Guide:

 · Ensure that base surfaces are clean, dry, firm and free from any loose or flaking material.

 · Apply the adhesive generously to the wall using a roller.

 · As a guide we recommend up to 2.5kg of paste per roll, more if the base surface is uneven or textured, where it is especially important to apply a thick bed of adhesive.

 · Cover an area sufficient to apply one length of Insulating Lining Paper Graphite+ at a time ensuring the pasted area exceeds the width of the Insulating Lining Paper Graphite+.

 · Use a brush or spatula to apply adhesive to areas the roller cannot reach.

 · The expanded polystyrene side of the product should be applied to the adhesive/wall.

 · Apply Insulating Lining Paper Graphite+ directly from the roll onto the wet adhesive and slide into place.

 · Smooth out any bubbles with a roller or similar. Leave a small amount of surplus material for trimming where necessary.

 · Cut off any excess material at the ceiling, floors and corners using a trimming knife in combination with a forming board.

 · On external corners the exposed edge of the material can be filled and sanded with flexible filler to give a neat finish.

 · Allow 48 hours for drying, longer if conditions are especially humid or cold.

 · We also recommend that Insulating Lining Paper Graphite+ is allowed to dry naturally and therefore recommend that heating is turned off whilst the wallcovering adhesive dries out.

 · Unless ambient temperatures are likely to drop below 10°c/50°F.

 · Any small gaps at seams and corners can be filled with flexible filler.

 · We recommend that the Insulating Lining Paper Graphite+ is lined with ‘Wallrock Fibreliner’, (this product is very strong, durable and dimensionally stable and compliments the Insulating Lining Paper Graphite+ perfectly).

 · The resulting surface is ready for painting or overhung with textured or printed wallcoverings.

 · Adhesive - we recommend Wallrock Thermal Liner Adhesive for application of this product or other solvent free adhesives suitable for hanging polystyrene veneers.

 · However, we cannot unfortunately accept responsibility for adhesion problems when an adhesive other than Wallrock Thermal Liner Adhesive has been used.

 · Important - inspect rolls carefully before beginning as we cannot accept claims for consequential loss in respect of any defects apparent prior to hanging.

 · Every effort is made to ensure all rolls reach you in perfect condition, but faults can occur from time to time.

 · Please retain all labels until the project is complete and you are satisfied with the results.

 · We will require them in the unlikely event you encounter a problem.

 · We recommend that after hanging no more than 2 lengths, the result is inspected before continuing.

 · Warning - surfaces painted prior to 1960 may contain lead pigments and special precautions should be taken when preparing these surfaces.

*Further information maybe found in our Downloads section.

Fairly easy access to all PDF files.

Datasheet ǀ Declaration of Performance - DoP ǀ BBA Certificate ǀ Installation Guide ǀ Certificates ǀ Brochure ǀ SPEC Sheet