Cordek Filcor Joint & Stick is a high performance, highly durable, flexible, waterproof, single component MS Polymer joint sealant and adhesive.

Joint & Stick is used to bond Filcor to most common materials used in construction and for fixing, jointing, and sealing formwork systems.

The product is fully compatible with Cordek Filcor and formwork systems and should be applied using a standard cartridge gun.

Filcor Joint & Stick is supplied in boxes containing 12no. 290ml cartridges and nozzles.

The 290ml cartridge will provide approximately 10 linear meters of 6mm diameter bead.

Specification:

Colour: White

Cartridge Size: 290ml

Shelf Life: 12 Months unopened

Temperature Resistance: -40⁰C to +100⁰C

Storage: +5⁰C to +25⁰C without direct sunlight

Application Temperature: +8⁰C to +30⁰C

Cordek Filcor Joint & Stick Features:

 · Flexible joint sealant and adhesive.

 · High performance joint sealant and adhesive.

 · Highly durable joint sealant and adhesive.

 · Fully waterproof joint sealant and adhesive.

 · Resists temperature from -40°C to 100°C.

 · Applied using a standard cartridge gun.

 · Approximate curing rate 3mm / 24h (23°C/50% R.H.).

 · Compatible with Cordek Filcor and formwork systems.

 · Single component MS Polymer joint sealant and adhesive.

 · Bonding, sealing, and joint detailing for Cordek formwork systems.

 · Bonding Filcor to Filcor and most common materials used in construction.

Cordek Filcor Joint & Stick Installation:

 · When bonding ensure that surfaces to be jointed/bonded are clean, dry, and free from dust, grease, or other contaminants as this can impede adhesion.

 · Apply adhesive to one surface in a wavy pattern using a manual or pneumatic cartridge gun then bring the two surfaces together immediately.

 · If a full bond is required, gun the adhesive onto the surface and comb out using an adhesive spreader prior to bringing the surfaces together.

 · It is important to leave a bond line with this type of elastomeric adhesive, i.e. the adhesive layer should be between 1-2mm thick, do not squeeze the bond line to zero.

 · Joint & Stick will bond in wet conditions, but the final strength may be reduced.

 · Prior testing is strongly recommended. Not suitable for use on Polypropylene, Polyethylene, Polythene and Teflon.

 · Formwork Jointing - Joint & Stick has been developed to enhance the connections of Cordek formwork, (formwork-to-formwork).

 · Bespoke formwork sections can be supplied with factory applied detailing on connecting edges in readiness for site applied Joint & Stick.

 · Cordek formwork sections are installed on-site with tightly butted connections.

 · Butt joints of adjoining sections are finished with the application of Joint & Stick, applied using a manual or pneumatic cartridge gun.

 · Apply Joint & Stick to the joint detail ensuring the bead remains slightly higher than the surface.

 · After application, use a sealant applicator dipped in soap water to smooth the finished joint.

 · Formwork sections can be masked using a suitable tape prior to the application of Joint & Stick for a neat and quick installation.

 · Tools can be cleaned with Methyl Ethyl Ketone (MEK), or acetone before the Joint & Stick sealant has completely cured.

 · Ensure any cleaning products, solvents, and organic materials do not come into contact with the Filcor (EPS).

 · For difficult materials with low surface energy, perform preliminary tests to determine whether a surface preparation is necessary.

 · Application Temperature: +8°C to +30°C.

*Further information may be found in our Downloads section.

Fairly easy access to all PDF files.

Datasheet ǀ Declaration of Performance - DoP ǀ BBA Certificate ǀ Installation Guide ǀ Certificates ǀ Brochure ǀ SPEC Sheet