Menu
Your Cart

Cedral® Weatherboard Cladding Tools

CEDRAL® CLADDING TOOLS

cedral installation toolsCedral® cladding tools are necessary cutting and measuring equipment used to fit correctly Cedral® Click System on the exterior wall in order to give weather protection all year round. In fact, fibre cement cladding boards such as Cedral® have become popular with architects as they allow them to design buildings with highly weather resistant exteriors and robust interiors. As you would expect they are typically tough and resist scratches and water. However, these materials are difficult to cut. It is also important to use the right method and tools for the application to ensure you have the finish needed when cutting very hard composite panels. When you get your composite cladding, it is important to make sure each plank is the correct size for your project and to do this you need to cut down each plank using the correct methods. The tools you will need depend on how much Cedral® cladding you plan to install. Remember to wear safety shoes, safety glasses, ear protection, a dust mask, gloves and any other safety equipment.

CEDRAL® CLADDING INSTALLATION TOOLS

You might find it easier to use the following tools:

Pencil | Knife | Hammer | Spirit level | Measuring tape | Chalk line | Hand saw | Square | Stapler | Microfibre | Metal snips | Cordless drill | Jigsaw | Circular saw | Step ladder | Vacuum cleaner | Corex protection board Saw blades

HOW TO CUT CEDRAL® CLADDING BOARDS?

There are actually several different ways for cutting the Cedral Weatherboard.

1. CEDRAL® BOARD CUT BY HANDSAW

First one on the list is the traditional Handsaw. It is a must have tool to any tradesman or DIY enthusiast. Handsaw is often used for either plastic or wood. They cut using both the push and pull stroke. Selecting the wrong blade for Cedral® boards may result in a raw finish, while selecting the right blade will result in a finer finish. Handsaws with fewer teeth are not recommended to cut Cedral® boards as they are best for fast, coarse cuts only. Also with this method, cutting from the back of the board is advisable as the saw guide leaves marks across the board surface.
Advice
Never use masking tape on cuts when working with wood grained structure. Tape won't stick to the raw surface as well as to a plain finish board. As earlier mentioned, cutting from the back will stop your board of chipping on edges. Why? When the saw is pulled up it pushes and presses the fibre-cement plank, avoiding chipping and tearing at the same time. By doing the other way round you will be pushing the material out and damaging board edges. If you decided to use a handsaw as a main tool to cut your Cedral® boards you should follow simple rules.

Rule 1. Don’t try to cut too fast!!
Remember! Boards are 3.6m long and 186mm wide. If you rush your cut through, you may end up splitting your board at the end. This is not something that you want to see, for sure.

Rule 2. Holding it down firmly.
Cedral® board should resist on a firm surface. Any movement may cause the board to crack in an unwanted direction. You will find that the straight edge will tend to shift during your cut, especially on long cuts, if you don’t have a firm grip on it and a lot of weight pressing down on it. That tends to ruin the cut and send you back in search of more material.

Rule 3. Test cutting is recommended.
By doing so you will see possible results. It's very important in situations where you don't want to pay for extra boards. Not using test technique may lead to more than one piece of panelling being discarded.

Rule 4. Measure twice, cut once.
The last thing that any of us need is to end up having to buy more material, because we found that we cut it off twice and it’s still too short. 
It is good practice to cut boards 20mm longer. Why? You will relieve the board of heavy off cuts. By having only a 20mm off cut you eliminate the risk of damaging the board.

2. CEDRAL® BOARD CUT BY ELECTRIC JIGSAW

While the method of cutting the boards with a handsaw is ideal for many situations, there are times when you can’t use it, such as when cutting a curve. So we need to look at a more conventional manner of how to cut Cedral panel. This is where the jigsaw takes its place. You’ll want to work from the back side of the panel as well, as that is the side that the saw will naturally splinter. It is best to work with a fine-toothed blade. This will provide a better finish, as they won’t go dull easily.

Is Jigsaw good for straight cuts?

Jigsaws can be great for cutting cladding panels but it can be hard to make a straight cut with them. The secret is to use a straightedge, which is clamped to the panel you are cutting. Cedral® fibre-cement board is very abrasive and dulls ordinary blades very quickly. While the blade works well at first, after a few cuts you will notice that the blade dulled quickly! If you use metal blades for fibre cement cutting material will literally eat up the teeth within a length of about 1 metre. It this situation is recommended to use Bosch T 141 HM circular jigsaw blade.

3. CEDRAL® BOARD CUT BY CIRCULAR SAW

Third method of cutting cladding boards will be Circular saw. When cutting fibre cement siding with handheld circular saw, you should use an appropriate blade. To keep dust to a minimum, use a circular saw that's equipped with either a dust collection bag. A hand held circular saw is ideal for cutting large quantities. It is ideal for shaving off overhanging edges of your project. For this type of tool you would be looking for a blade with polycrystalline diamond teeth that cut effortlessly through high quality composite panels. For the best quality cuts it is crucial to make sure the blade does not protrude more than 1-2mm out of the base of application. And again, cutting from the back of the board is advisable as the saw guide leaves marks across the board surface. As mentioned earlier, test cutting is recommended. 
Circular saw produces a clean cut. It eliminates the need to try and make good. Saw blades are available in a number of diameters ranging from 160 to 230 millimetres. A 4 tooth blade on a 180mm diameter blade is recommended for cutting.

What are disadvantages of cutting Cedral® cladding boards with circular saw?

The cost of the circular tungsten blades can run as dear as £120. So something that’s not going to get used perhaps for job after job after job maybe that is a consideration too.

4. CEDRAL® BOARD CUT BY ANGLE GRINDER

You can also cut Cedral® board with an angle grinder fitted with a diamond-impregnated cutting wheel, but this tool produces a lot of dust and is harder to control than a circular saw. 
Some people still use angle grinder as the only tool to cut Cedral® planks. Some people say “this is the worst option to choose”. Why? Because of Dust! We all know that dust is not a healthy thing to breathe.

5. CEDRAL® BOARD CUT BY MITRE SAW

Our last tool is mitre saw. This tool can deliver smooth and accurate cuts along the length of your composite panel. It is an excellent tool to achieve straight clean cuts and multiple angles. An ideal solution for achieving both cross cuts and mitre cuts.

 
CEDRAL® CLADDING FREQUENTLY ASKED QUESTIONS

How do I make holes in Cedral® boards?

Simply equip a jigsaw with a metal cutting blade. To start the saw in fibre-cement board, drill a hole through the Cedral cladding board large enough for the jigsaw blade.

Do I need to clean Cedral® boards after cutting?

Yes, always make sure that after cutting you wipe away dust with a clean, dry cloth.

Can I cut the Cedral® board with a utility knife?

This type of cladding is difficult to cut. If you cut Cedral® fibre cement board with a utility knife it will take you forever.

 

Related articles:

Fibre cement cladding technology

Choose what’s the right cladding system for your home, inside and out

Cedral® cladding. Short and direct answers

Cedral cladding installers

How to install Cedral Click Cladding

How to install Cedral Lap Cladding

How to clean fibre cement cladding?

How to cut cladding boards?

Weatherboard Touch Up Paint for Cedral.

How much is Cedral cladding per square Metre?

Cedral Colour Chart

Cedral Weatherboard. Timeless façade board or temporary solution?

Cedral Cladding: Benefits

                                                                           

160mm Fibre-Fast Diamond Tipped Blade for Cedral Planks
CLICK & LAP
Brand: Cedral® Model: 160mm - Diamond Tipped Blade
160mm FibreFast Diamond Tipped Blade for Cedral Planks is a saw blade with polycrystalline diamond (PCD) teeth that cut through fibre cement board products such as Cedral Weatherboard Cladding. The Blade is suitable for: handheld circular saws, mitre and chop saws which allow for a 30mm bore size..
  • Cleaner Cut
  • Less Dust
  • Extra Thin Kerf
  • Fibre-Fast Diamond Tipped Blade
  • Material: Polycrystalline Diamond (PCD)
£ 109.88
Ex Tax:£ 91.57
Estimated delivery: 2-3 working days
184mm Fibre-Fast Diamond Tipped Blade for Cedral Planks
CLICK & LAP
Brand: Cedral® Model: 184mm - Diamond Tipped Blade
184mm FibreFast Diamond Tipped Blade for Cedral Planks is a saw blade with polycrystalline diamond (PCD) teeth that cut through fibre cement board products such as Marley Cedral Weatherboard Cladding. FibreFast Blade is suitable for: handheld circular saws, mitre and chop saws which allow for a 3..
  • Cleaner Cut
  • Less Dust
  • Extra Thin Kerf
  • Fibre-Fast Diamond Tipped Blade
  • Material: Polycrystalline Diamond (PCD)
£ 113.88
Ex Tax:£ 94.90
Estimated delivery: 2-3 working days
230mm Fibre-Fast Diamond Tipped Blade for Cedral Boards
CLICK & LAP
Brand: Cedral® Model: 230mm - Diamond Tipped Blade
230mm FibreFast Diamond Tipped Blade for Cedral Boards is a special saw blade with polycrystalline diamond (PCD) teeth that cut through fibre cement board products such as Marley Cedral Weatherboard Cladding. The Blade is suitable for: handheld circular saws, mitre and chop saws which allow for a..
  • Cleaner Cut
  • Less Dust
  • Extra Thin Kerf
  • Fibre-Fast Diamond Tipped Blade
  • Material: Polycrystalline Diamond (PCD)
£ 147.00
Ex Tax:£ 122.50
Estimated delivery: 2-3 working days
Showing 1 to 3 of 3 (1 Pages)