Wallrock Thermal Liner Adhesive 10kg Tub is a strong, water based adhesive especially formulated for Wallrock wallpapers, insulation products, PUR sound and latex insulation.

This special Wallrock Adhesive provides high wet tack to hold while cutting and positioning for optimum adhesion to surface.

Wallrock Thermal Liner Adhesive allows walls to breathe, resists moisture and prevents mould, yeast and fungal growth.

Easy roll formula for quick and easy application directly to the wall using a roller or brush.

Typical consumption of 2m² to 1.5m² per kg.

Specification:

Coverage: 2m² to 1.5m² per kg

Material: Adhesive

Profile: Ready-to-use

Applications: Walls and ceilings

Wallrock Thermal Liner Adhesive Features:

 · High performance aqueous adhesive with fillers.

 · Thick, smooth, low splatter formula - roll or brush straight from the tub.

 · High wet tack to hold while cutting and positioning.

 · High resin content for optimum adhesion to surface.

 · Allows walls to breathe and resists moisture.

 · Contains an inhibitor to prevent mould, yeast and fungal growth.

 · Can be used to hang Wallrock Thermal Liner KV600.

 · Can be used to hang Wallrock Thermal Liner.

 · Can be used to hang Wallrock R300 Cosy Liner.

 · Can be used to hang PUR Sound Insulation.

 · Can be used to hang Insulating Lining Paper.

 · Can be used to hang Insulating Lining Graphite+.

 · Can be used to hang Latex Sound Insulation.

 · Can be used to hang Heatsaver Wall Underliner.

Wallrock Thermal Liner Adhesive Installation Guide:

 · This product is ready-mixed and ready to use, however some storage conditions may contribute to separation of water, visible on top of the product.

 · This can be easily stirred into the bulk of the product without affecting the performance properties of the product.

 · Despite stringent quality assurance procedures, defects may occur in exceptional cases from time to time.

 · If a fault is found, please return any defective material to the place of purchase.

 · Please see wallpaper roll labels for hanging instructions for each individual lining system.

 · Surface Preparation - Wallrock Thermal Liner Adhesive can be used on most internal wall surfaces.

 · The adhesive contains filler and can be used in conjunction with our wallcovering products to cover surface imperfections and textures.

 · All surfaces should be firm, dry and clean, all loose material should be removed before the adhesive is applied.

 · Major surface imperfections should also be filled and levelled in preparation.

 · Drywall and other absorbent surfaces should be sized and completely left to dry for at least 4 hours before application of the adhesive.

 · Each adhesive container holds 5kg (11lb) or 10kg (22lb), sufficient for 1/2 or 1 roll of Wallrock Thermal Liner KV600, 1 roll or 2 rolls of Wallrock Thermal Liner or 1.5 rolls or 3 rolls of wallrock R300 Cosy Liner.

 · Where the surface being covered is flat and in relatively good condition coverage will improve significantly by up to 25%.

 · Adhesive Application - The room temperature and that of the adhesive should not be less than 10°C/50°F.

 · Important - Please keep the adhesive sealed when not in use.

 · Generously apply the adhesive directly to the wall using a deep pile roller, use more paste if the wall is textured or damaged.

 · Apply adhesive to an area a little wider than for one length, this will ensure an adequate area is covered and make the next length easier to apply.

 · In the areas which the roller cannot reach, such as corners, the paste should be applied with a spatula or brush.

 · Each length of wallcovering should be butt jointed. Remove excess glue immediately with a damp cloth or sponge.

 · Drying time depends upon room temperature, humidity, thickness of the paste layer and surface absorbency but is normally complete after 24 hours.

 · In some circumstances you may have to wait longer before any other wallcoverings are applied to the Thermal Liner.

 · Check for adhesion before commencing any subsequent redecoration.

 · The adhesive may be used to fill any small gaps at the seams, smooth down using sandpaper before decoration.

 · Important -  Do not thin or add water to the adhesive.

 · Contains fungicide and biocide to inhibit mould, yeast and bacteria.

 · Keep away from children and animals. Wash hands thoroughly after use.

 · Do not empty into drains or watercourses.

 · Waste should be disposed of using authorised disposal routes and sites.

*Further information may be found in our Downloads section.

Fairly easy access to all PDF files.

Datasheet ǀ Declaration of Performance - DoP ǀ BBA Certificate ǀ Installation Guide ǀ Certificates ǀ Brochure ǀ SPEC Sheet