Menu
Your Cart

150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)

150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
  • 150mm Unilin XT/HYF HYFLOOR Thin-R Plus Floorboard Premium PIR
  • For use with underfloor heating, ground supported and suspended floors
  • Excellent lambda value (Thermal conductivity) of 0.021 W/mK
  • Unilin XT/HYF Meets U-Values specified in the Building Regulations
  • Improving the overall U-Value of the floor (XT/HYF HYFLOOR)
Estimated delivery:
In Stock
£ 345.60
Ex VAT: £ 288.00

Options available

150mm Floor Insulation Board Unilin XT/HYF, consisting of a rigid polyisocyanurate core between low emissivity gas tight facings used for underfloor heating applications.

Unilin Hyfloor XT/HYF has a superior thickness to performance ratio, allowing the lower targets required under Building Regulations to be achieved with minimum thickness.

XT/HYF T&G jointing system offers a practical on-site solution that results in a more robust continuous layer of insulation, minimising the threat of thermal bridging.

Unilin Floor Boards are tongue and grooved insulation panels with high compressive strength of 140kPa and very good thermal properties.

Floorboards should be laid staggered in a break bonded pattern and fitted tightly at edges and around any service penetrations.

XT/HYF insulation is the answer to achieve lower U-Values – in a practical and robust manner.

The XT/HYF PIR floorboard achieves an A + rating under the BRE Green Guide.

 

Specification:

 

Thickness: 150mm

Width: 1200mm

Length: 2400mm

Size: 150mm x 1200mm x 2400mm

Board Coverage: 2.88m2

Pack Coverage: 5.76m2

Profile: Tongue & Groove

R-Value: 7.10 m2K/W

Thermal Conductivity: 0.021 W/mK

Reaction to Fire: NPD

Compressive Strength: >140 (kPa)

 

Unilin XT/HYF HYFLOOR Thin-R Plus Features:

 · Reduced insulation thickness.

 · Excellent 0.021 W/mK Lambda value.

 · High compressive strength >140 (kPa).

 · Suitable for underfloor heating.

 · Perimeter strips for robust detailing.

 · Fully engineered Tongue & Groove jointing.

 · Minimising the threat of Thermal Bridging.

 · Improving the overall U-Value of the floor.

 · Meets U-Values specified in the Building Regulations.

 · Suitable for ground supported floors.

 · Suitable for suspended floors.

 

Unilin XT/HYF HYFLOOR Thin-R Plus Installation Guidelines:

 · Below Concrete Slab - Lay and level the hardcore in layers 150mm min / 250mm max and compact well.

 · Sand blind base to create a level surface and to protect DPM.

 · The damp proof membrane (DPM), normally 1200g polythene or radon barrier, should be laid over the blinding, tape lapped joints to prevent passage of ground moisture.

 · Carry DPM up to the wall to meet and seal with the DPC course.

 · Contact the membrane manufacturer for further guidance on installation and best practice.

 · Lay the Hyfloor across the DPM.

 · If two layers are required, lay the boards in a staggered jointed pattern.

 · Closely butt all edges.

 · Place Unilin Perimeter Strips (XT/STR) around floor perimeter to provide robust detailing in order to reduce Thermal Bridging.

 · Ensure the top of the perimeter strip is level with top of floor finish.

 · Seal around any service penetrations.

 · Lay a thin gauge polythene sheet, to act as a separating layer, over the insulation with 150mm lap joints.

 · VCL should be taped at the joints to ensure a continuous separating layer, as per BRE GBG 45 “Insulating Ground Floors”.

 · If underfloor heating is required, lay pipes and clip to the Hyfloor through the separating layer.

 · Follow UFH manufacturer’s guidelines.

 · Pour and compact concrete slab to required finish floor level.

 · Below Floor Screed - Lay and level the concrete slab, allowing sufficient time to dry out, as per BS 8203.

 · Beam and block floors may need a levelling screed or grouting to ensure base level.

 · Refer to manufacturer’s guidelines.

 · The damp proof membrane (DPM), normally 1200g polythene or radon barrier, should be laid over the blinding, tape lapped joints to prevent passage of ground moisture.

 · Carry DPM up to the wall to meet and seal with the DPC course.

 · Contact the membrane manufacturer for further guidance on installation and best practice.

 · Lay the Hyfloor boards across the DPM.

 · If two layers are required, lay the boards in a staggered jointed pattern.

 · Closely butt all edges.

 · Place Unilin Perimeter Strips around the floor perimeter to provide robust detailing in order to prevent Thermal Bridging.

 · Ensure the top of the perimeter strip is level with the top of the floor finish.

 · Seal around any service penetrations.

 · Lay a thin gauge polythene sheet, to act as a separating layer, over the insulation with 150mm lap joints.

 · VCL should be taped at the joints to ensure a continuous separating layer, as per BRE GBG 45 “Insulating Ground Floors”.

 · If underfloor heating is required, lay pipes and clip to the Hyfloor through the separating layer.

 · Follow manufacturer’s guidelines.

 · Pour screed according to screed manufacturer’s guidelines.

 

*Further information may be found in our Downloads section.

Fairly easy access to all PDF files.

Datasheet ǀ Declaration of Performance - DoP ǀ BBA Certificate ǀ Installation Guide ǀ Certificates ǀ Brochure ǀ SPEC Sheet 

*Special Product - Non returnable cancelable.

specification
Board covarage 5.76 m2
Colour Light yellow
Compressive Strength 140 kPa (10% Compression)
Length 2400mm
Material Enhanced PIR Rigid Foam
Pack Coverage 5.76m2
Profile Engineered Tongue & Groove
R-Value 5.95 m2K/W
Size 125mm x 1200mm x 2400mm
Thermal Conductivity 0.021 W/mK
Thickness 125mm
Width 1200mm
Fire Classification NPD
Building Regulations Compatible
Coverage 2.88m2 (1 board)
Finish Low emissivity gas tight foil facings
Quantity 2 sheets
Shipping method Articulated Vehicle ǀ Courier
Grade UFH Floorboard
Applications Underfloor heating, ground supported and suspended floors
BBA Certified Yes
Type Enhanced Performance PIR Rigid Foam
Vapour Control Layer Yes
Fixing method Tongue & Groove jointing
Foil faced Yes, gas tight foil facings
ETA Notification Yes
U-value 0.12 W/m²K
Features Superior thickness to performance ratio
Manufacturer Unilin Insulation®

Write a review

Note: HTML is not translated!
Bad Good

We deliver insulation materials to Mainland UK only. Deliveries to Highlands, Northern Ireland, Isle of Wight etc.. might be possible at additional cost.
We offer free delivery on most of the orders above £300 (excluding VAT) (except special products - shipping cost via courier - products marked ''Request A Quote'')

Delivery of some insulation materials might be extended due to the current situation (Covid-19, stock shortages, allocations).
If you need materials quickly please contact us - we will do our best to help you source materials needed.

We do not deliver on weekends and bank holidays. Sometimes we can deliver on Saturdays - please check with us before placing the order.
If you need any further information please contact us tel. 02081910776

We can help to calculate price per m2 or linear meter (one meter in length) cost, please just contact us via phone 02081910776, email or live chat. Alternatively, you can work it out yourself quickly and easily: to get cost per meter square please divide price shown in orange area by ''Required area (m2)'' Example price of £28.80 divided by board coverage 2.88m2 = cost of £10.00 per m2.

INSTALLERS

No matter whether you choose a local installer or a national company, there’s a few tips to help you find the right installer for your home insulation improvements, such as asking for recommendations and making sure that they’re part of a certification scheme. This makes sure that they have the right skills and standards of workmanship to carry out the installation, and you can be sure that they know exactly what they are doing.

4 TIPS FOR CHOOSING THE BEST INSULATION INSTALLER

1. Thermal inspection picture in portfolio

It’s worth seeing a installer’s previous work. There’s no harm asking if you can see any properties nearby that they’ve installed insulation in. Best way would be to see Infrared Thermal Imaging Inspections. Thermal cameras spot small, but key changes in temperature in different areas of a house, identifying problematic areas that the human eye never could and some that a visual inspection could only hypothesize.

2. Reviews

Along with checking recommendations and previous work, finding reviews online can often be a great way to find out if they provide a good service or not. However, it’s best not to solely rely on reviews you may find or review websites, as there’s no controlling who writes them.

3. Compare prices

Comparing prices will also ensure companies can’t take advantage of you and give you a fair price. 

4. Word of Mouth

The best way to find a great insulation installer is through recommendations. Make sure you ask friends and family. They will most likely give you their honest opinion and can tell you from first hand experience.

 

Whether you require a wall, cladding, external wall, loft or floor insulation fitted, you can find and hire your local insulation installers from popular UK web pages. A simple internet search will return thousands of potential installers near your area.

 

https://www.nia-uk.org/find-an-installer/

https://www.checkatrade.com/

https://www.mybuilder.com/

https://www.ratedpeople.com/local-thermal-insulation

 

STOCKIST

We are the stockist of construction materials and related products for both trade and DIY from most recognizable brands in the UK like Cordek, RCM, Promat, Rockwool, Isover, Celotex, Xtratherm, Ursa, Low-E, Cedral, Kingspan, Dufaylite, British Gypsum, K-rend, Ecotherm, Iko enertherm, Kay-Metzeler, Terrawool to allow you to complete your insulation job on time at competitive prices and the highest standards.

 

Whether you are a large company or a DIYer, if you need a large amount of insulation materials, we can offer quantity discounts at the best prices. Please contact us and our friendly customer service will try to find the best and cheapest solutions for you. We value your time and we will try to deliver the products as soon as possible at a reasonable price to your construction site or house. The UK's leading insulation supplier near you and your needs. Price List available upon request.
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
150mm Floor PIR Insulation Board Unilin XT/HYF T&G (pack of 2)
£ 345.60