100mm Unilin ECO/MA 360 Floor Insulation is a bio-enhanced, superior performance PIR rigid foam insulation board suitable for underfloor heating, solid and suspended floors.

It is lightweight, easy to install and combines high compressive strength with low thermal conductivity, providing a high performance solution for floor insulation.

Unilin ECO360 MA (Floorboard) has the strength and thermal properties required to reach the high performance U-Values specified in the Building Regulations.

ECO360 MA Bio Enhanced Insulation for Floors offers excellent insulation performance with a thermal conductivity (lambda value) of 0.020 W/mK.

Using pioneering environmentally conscious technology, ECO360 MA in floor applications will reduce heat loss while also delivering excellent thermal bridging details.

This bio-enhanced insulation will significantly improve the U-Value of new and existing floors.

The product packaging is biodegradable and the overall content has been reduced significantly.

Unilin ECO360 Floor Board offers a bio-enhanced formulation which is halogen free.

ECO360 is a part of a design solution to achieve RIBA/RIAI Climate Challenge 2030, LETI Standards and the Future Homes Hub targets.

Specification:

Thickness: 100mm

Width: 1200mm

Length: 2400mm

Size: 100mm x 1200mm x 2400mm

Board Coverage: 2.88m2

Pack Coverage: 11.52m2

Profile: Square Edge

R-Value: 5.00m2K/W

Thermal Conductivity: 0.020 W/mK

Reaction to Fire: NPD

Compressive Strength: >150 (kPa)

Unilin ECO360 Floorboard Features:

 · Halogen free.

 · Biodegradable packaging.

 · High compressive strength.

 · Suitable for underfloor heating.

 · Suitable for solid and suspended floors.

 · Bio-enhanced PIR rigid foam insulation.

 · Achieve RIBA/RIAI Climate Challenge 2030

 · Enhanced performance lambda as low as 0.020 W/mK.

 · Improves the U-Value of new and existing floors.

 · Meets U-Values specified in the Building Regulations.

 · Achieve LETI Standards and the Future Homes Hub targets.

Unilin ECO360 Floorboard Installation:

Below Concrete Slab:

 · Lay and level the hardcore in layers 150mm min/250mm max and compact well.

 · Sand blind base to create a level surface and to protect DPM.

 · The damp proof membrane (DPM), normally 1200g polythene or radon barrier, should be laid over the blinding, tape lapped joints to prevent passage of ground moisture.

 · Carry DPM up to the wall to meet and seal with the DPC course (contact the membrane manufacturer for further guidance on installation and best practice).

 · Lay the ECO360 MA for floors across the DPM.

 · If two layers are required, lay the boards in a staggered jointed pattern.

 · Closely butt all edges.

 · Place Unilin Perimeter Strips (XO/STR) around floor perimeter to provide robust detailing in order to reduce Thermal Bridging.

 · Ensure the top of the perimeter strip is level with the top of the floor finish.

 · Seal around any service penetrations.

 · Lay a thin gauge polythene sheet, to act as a separating layer, over the insulation with 150mm lap joints.

 · VCL should be taped at the joints to ensure a continuous separating layer, as per BRE GBG 45 “Insulating Ground Floors”.

 · If underfloor heating is required, lay pipes and clip to the insulation boards through the separating layer.

 · Follow UFH manufacturer’s guidelines.

 · Pour and compact concrete slab to required finish floor level.

Below Floor Screed:

 · Lay and level the concrete slab, allowing sufficient time to dry out, as per BS 8203.

 · Beam and block floors may need a levelling screed or grouting to ensure base level (refer to manufacturer’s guidelines).

 · The damp proof membrane (DPM), normally 1200g polythene or radon barrier, should be laid over the blinding, tape lapped joints to prevent passage of ground moisture.

 · Carry DPM up to the wall to meet and seal with the DPC course (contact the membrane manufacturer for further guidance on installation and best practice).

 · Lay the ECO360 MA for floors boards across the DPM.

 · If two layers are required, lay the boards in a staggered jointed pattern.

 · Closely butt all edges.

 · Place Unilin Perimeter Strips (XO/STR) around floor perimeter to provide robust detailing in order to prevent Thermal Bridging.

 · Ensure the top of the perimeter strip is level with top of floor finish.

 · Seal around any service penetrations.

 · Lay a thin gauge polythene sheet, to act as a separating layer, over the insulation with 150mm lap joints.

 · Separating layers should be taped at the joints to ensure a continuous separating layer, as per BRE GBG 45 “Insulating Ground Floors”.

 · If underfloor heating is required, lay pipes and clip to the insulation boards through the separating layer.

 · Follow manufacturer’s guidelines.

 · Pour screed according to screed manufacturer’s guidelines.

Suspended Timber Floor:

 · Install joists in the normal manner, ensuring adequate ventilation.

 · Measure gaps between joists and cut ECO360 MA for floors to size, allowing for variations in joist spacings.

 · Mechanically fasten treated timber battens to the joists, allowing for correct thickness of insulation.

 · Galvanised nails or saddle clips may also be used, ensuring nails are left 40mm proud of the joists.

 · Install ECO360 MA for floors between joists with joints tightly butted and seal any gaps with expanding foam.

 · If two insulation layers are required, lay the boards in a staggered jointed pattern, also sealing any gaps with expanding foam.

 · Floor boards should be laid directly to the joists.

Certification and standards:

 · BBA Certification No.12/4956.

 · BS EN ISO 9001 Quality Management System.

 · BS EN ISO 14001 Environmental Management System.

 · BS EN 13165.

*Further information may be found in our Downloads section.

Fairly easy access to all PDF files.

Datasheet ǀ Declaration of Performance - DoP ǀ BBA Certificate ǀ Installation Guide ǀ Certificates ǀ Brochure ǀ SPEC Sheet 

*Special Product - Non returnable cancelable.