100mm Unilin ECO/MA 360 Roof Insulation is a bio-enhanced, superior performance PIR rigid foam insulation board suitable for sloped roofs (ventilated, hybrid or warm roof).

Using pioneering environmentally conscious technology, ECO360 MA in roof applications will reduce heat loss while also delivering excellent thermal bridging details.

ECO/MA Roof is a lightweight, easy to install and combines high compressive strength with low thermal conductivity, providing a high performance solution for roof insulation.

Unilin ECO360 MA (Roof board) has the strength and thermal properties required to reach the high performance U-Values specified in the Building Regulations.

ECO360 MA Bio Enhanced Insulation for roofs offers excellent insulation performance with a thermal conductivity (lambda value) of 0.020 W/mK.

This bio-enhanced insulation will significantly improve the U-Value of new and existing roofs.

The product packaging is biodegradable and the overall content has been reduced significantly.

Unilin ECO360 Roof Board offers a bio-enhanced formulation which is halogen free.

ECO360 is a part of a design solution to achieve RIBA/RIAI Climate Challenge 2030, LETI Standards and the Future Homes Hub targets.

Specification:

Thickness: 100mm

Width: 1200mm

Length: 2400mm

Size: 100mm x 1200mm x 2400mm

Board Coverage: 2.88m2

Pack Coverage: 11.52m2

Profile: Square Edge

R-Value: 5.00m2K/W

Thermal Conductivity: 0.020 W/mK

Reaction to Fire: NPD

Compressive Strength: >150 (kPa)

Unilin ECO360 Roof Insulation Features:

 · Halogen free.

 · Suitable for sloped roofs.

 · Suitable for ventilated roofs.

 · Suitable for hybrid roofs.

 · Suitable for warm roofs.

 · Biodegradable packaging.

 · High compressive strength.

 · Bio-enhanced PIR rigid foam insulation.

 · Achieve RIBA/RIAI Climate Challenge 2030

 · Enhanced performance lambda as low as 0.020 W/mK.

 · Improves the U-Value of new and existing roofs.

 · Meets U-Values specified in the Building Regulations.

 · Achieve LETI Standards and the Future Homes Hub targets.

Unilin ECO360 Roof Board Installation Guidelines:

Ventilated Roof Installation:

 · Position and fix battens to the inner face of rafters, flush with the top edge of the timber.

 · Allow for ventilation gaps, normally 50mm, (May be reduced depending on breather membrane certification).

 · Cut boards with fine toothed saw to fit tightly between rafters, flush with the bottom of the rafter.

 · Allow slight oversize of cut to achieve ‘friction fit’ and seal any gaps with expanding foam.

 · A second continuous layer of insulation should be fixed to the underside of the rafter.

 · Run the second layer transverse to the first with joints tightly butted.

 · Fix with clout nails to hold insulation in place until plasterboard is installed.

 · Provide a separate vapour control layer between insulation and plasterboard or alternatively, tape the joints of the insulation with an aluminium foil tape.

 · Finish with plasterboard fixed with dry lining screws.

 · Screw fix every 150mm, 12mm from edge of boards, ensuring a minimum 25mm penetration into the rafter or alternatively follow plasterboard manufacturer installations guidance.

Hybrid Roof Installation:

 · Follow the same procedure as in the ventilated roof except a breather membrane is used above the rafter allowing the 50mm ventilation space to be dispensed with.

 · Typically, a 25mm unventilated void should be maintained; Agrément certification covering the membrane should be consulted.

Warm Roof Installation:

 · Ensure cavity wall insulation has continued to roof height to meet with the roof insulation.

 · Fix a treated timber stop rail to the end of the rafter at the eaves.

 · Lay ECO360 MA Roofs staggered jointed over the rafters.

 · Ensure joints are tightly butted and fill any gaps with expanding foam.

 · Joints should be fully supported by rafters.

 · Boards can be temporarily fixed with nails.

 · Fix 38mm x 50mm counter battens with approved fixings through the insulation board into the rafter.

 · The amount of fixings is determined by the fixing manufacturer who can also provide wind load calculations.

 · A breathable sarking membrane should be fitted; refer to manufacturer’s Agrément certification.

 · Ventilation may have to be provided subject to that certification and minimises the risk of interstitial condensation forming on the underside of the membrane.

 · Providing an unventilated void under the membrane can improve thermal performance.

 · Secure 50mm x 25mm tiling battens through counterbatten and ECO360 MA Roofs to the rafter.

 · If an additional second layer is required, this should be fixed between the rafters.

 · Cut boards with fine toothed saw to fit tightly between rafters, flush with the top of the rafter.

 · Allow slight oversize of cut to achieve ‘friction fit’ and seal any gaps with expanding foam.

 · Provide a separate vapour control layer between the bottom of the rafter and plasterboard.

 · Finish with plasterboard fixed with dry lining screws.

 · Screw fix every 150mm, 12mm from edge of boards ensuring a minimum 25mm penetration into the rafter or alternatively follow plasterboard manufacturer installations guidance.

Certification and standards:

 · BBA Certification No.12/4956.

 · BS EN ISO 9001 Quality Management System.

 · BS EN ISO 14001 Environmental Management System.

 · BS EN 13165.

*Further information may be found in our Downloads section.

Fairly easy access to all PDF files.

Datasheet ǀ Declaration of Performance - DoP ǀ BBA Certificate ǀ Installation Guide ǀ Certificates ǀ Brochure ǀ SPEC Sheet 

*Special Product - Non returnable cancelable.