Menu
Your Cart

30-50mm Unilin TR/MG Tapered Roof Insulation (pack of 6)

30-50mm Unilin TR/MG Tapered Roof Insulation (pack of 6)
30-50mm Unilin TR/MG Tapered Roof Insulation (pack of 6)
30-50mm Unilin TR/MG Tapered Roof Insulation (pack of 6)
30-50mm Unilin TR/MG Tapered Roof Insulation (pack of 6)
30-50mm Unilin TR/MG Tapered Roof Insulation (pack of 6)
30-50mm Unilin TR/MG Tapered Roof Insulation (pack of 6)
30-50mm Unilin TR/MG Tapered Roof Insulation (pack of 6)
  • 30-50mm Unilin TR/MG Tapered Roof Insulation Board (1200x1200mm)
  • High Performance PIR insulation board with mineral coated glass facers
  • TR/MG can be used below single ply fully adhered roof membranes
  • Can be used in waterproofing systems and partially bonded built-up felt
  • Practical solution to water ponding with insulation and drainage in a single system
Estimated delivery:
In Stock
£ 294.35
Ex VAT: £ 245.29

Options available

30-50mm Unilin Tapered Roof TR/MG is a high performance PIR with mineral coated glass facers used below single ply fully adhered roof membranes, waterproofing systems and partially bonded built-up felt.

Unilin TR/MG tapered roof insulation boards are embedded in a layer of bitumen on a 3G type felt to BS EN 13707: 2013 (Reinforced bitumen sheets for roof waterproofing that has been adhered to the deck).

TR/MG board is a practical solution to water ponding with insulation and drainage in a single system or mechanically fixed roof membrane systems and most partially bonded built-up felt systems.

Unilin TR/MG, a rigid thermoset PIR mineral-coated glass-fibre faced board used as a thermal insulation and to create or improve falls on limited access concrete, timber or metal decks.

These tapered roof insulation boards should be laid over the vapour control layer in a break bonded pattern.

The long edges of the boards should be laid at right angles to the corrugations and all board joints must be fully supported by the deck.

The boards are generally secured by  approved mechanical fixings or adhered using other suitable adhesive.

The requirement for a separate vapour control layer should be assessed in accordance with BS 6229.

Tapered Roof TR/MG is suitable for use on roof decks that are subject to maintenance traffic.

 

Specification:

 

Thickness: 30-50mm

Width: 1200mm

Length: 1200mm

Size: 30-50mm x 1200mm x 1200mm

Board Coverage: 1.44m2

Pack Coverage: 8.64m2

Boards in pack: 6 sheets

Profile: Square Edge

R-Value: 1.25m2K/W – 2.08m2K/W

Density (Foam Core): 32kg/m3 

Thermal Conductivity: 0.024W/mK

Compressive Strength: >150 (kPa)

Reaction to Fire: Euroclass B, s2-d0

 

Tapered Roof Unilin TR/MG Features:

 · Mineral coated glass facers.

 · BBA certified (11/4817).

 · High thermal performance.

 · Easy to handle and install.

 · Unique tapered profiled boards.

 · High compressive strength >150 kPa.

 · Available in 1200mm x 1200mm sheets.

 · Used below single ply fully adhered roof membranes.

 · Used in waterproofing systems and partially bonded built-up felt.

 · Suitable for new build and refurbishment roofs.

 · Practical solution to water ponding with insulation and drainage in a single system.

 

Unilin TR/MG Tapered Flat Roof Board Installation Guide:

 · Decks should be dry and clean of debris with tapered components laid to achieve the designed falls.

 · The boards can be secured using approved mechanical fixings and washers, with boards laid with a break bonded pattern or can be adhered using other suitable adhesive.

 · Joints should be closely butted.

 · The tapered boards should be laid over the vapour control layer in a break bonded pattern.

 · The boards are generally secured by approved mechanical fixings.

 · The waterproofing is also mechanically fixed in accordance with the specific manufacturer’s instructions.

 · Laying (Concrete Deck) - Decks should be dry and clean of debris.

 · The boards can be secured using approved mechanical fixings and washers, with boards laid with a break-bonded pattern.

 · Joints should be closely butted.

 · Alternatively the boards can be adhered to the decking with approved adhesive systems.

 · Partially bonded built–up felt waterproofing should be laid, where in accordance with BS 8217 (Reinforced bitumen membranes for roofing code of practice).

 · Fully Adhered Systems - The boards are suitable for use with most fully adhered single-ply waterproofing membranes.

 · Board joints and abutments should be taped subject to the approved adhesive system being used.

 · A fleece backed membrane might be required with the system being used, check with the system manufacturer.

 · The facing of these boards should not be considered as temporary waterproofing, when work is interrupted or at the end of each day, a night joint must be made to prevent water penetration.

 · Unilin TR/MG tapered boards should be waterproofed as soon as possible after fixing.

 · Fixings - Depending on the fixings specification chosen, quantity and pattern of fixings will vary with the location, roof height/width and topographical data.

 · Architectural specifications should be consulted.

 · Generally with 1200mm x 1200mm boards, a minimum of 4 fixings per board are adequate, located between 50mm and 150mm from all edges.

 · If more than one layer of insulation is being used, the flat board packers should be mechanically fixed with a minimum of one fixing before fixing profiled boards.

 · Additional fixings around the roof perimeter of the roof may be required.

 · Countersunk washers, 50mm in diameter, should be used with each fixing.

 · However, BS 6399 Part 2 or BS EN 1991-1.4: 2005 + A1: 2010 (National Annex to Eurocode 1.Actions on structures. General Actions. Wind Actions) should always be consulted.

 · It is recommended to seek advice from the fixing manufacturer for specific guidance.

 · Countersunk washers, 50mm in diameter, should be used with each fixing.

 

Unilin Thin-R TR/MG Certification and Standards:

 · BBA Certification No. 11/4817. 

 · BS EN ISO 9001 Quality Management System.

 · BS EN ISO 14001 Environmental Management System.

 

*Further information may be found in our Downloads section.

Fairly easy access to all PDF files.

Datasheet ǀ Declaration of Performance - DoP ǀ BBA Certificate ǀ Installation Guide ǀ Certificates ǀ Brochure ǀ SPEC Sheet 

*Special Product - Non returnable cancelable.

specification
Board covarage 8.64 m2
Colour Light yellow
Density 32 Kg/m3
Length 1200mm
Material Polyisocyanurate Rigid Foam
Pack Coverage 8.64m2
Pack Quantity 6 sheets
Profile Square Edge
R-Value 1.25m2K/W - 2.08m2K/W
Size 30-50mm x 1200mm x 1200mm
Thermal Conductivity 0.024 W/mK
Thickness 30-50mm
Width 1200mm
Fire Reaction Euroclass B, s2-d0
Finish Vapour resistant gas-tight foil
Shipping method Articulated Vehicle ǀ Courier
Applications Roof membranes, Waterproofing systems, Built-up felt
BBA Certified Yes (No. 11/4817)
Fixing method Mechanically fixed
Foil faced No, Mineral Glass Fibre Facings
ETA Notification Yes
Features Practical solution to water ponding with insulation and drainage
Manufacturer Unilin Insulation®

Write a review

Note: HTML is not translated!
Bad Good

We deliver insulation materials to Mainland UK only. Deliveries to Highlands, Northern Ireland, Isle of Wight etc.. might be possible at additional cost.
We offer free delivery on most of the orders above £300 (excluding VAT) (except special products - shipping cost via courier - products marked ''Request A Quote'')

Delivery of some insulation materials might be extended due to the current situation (Covid-19, stock shortages, allocations).
If you need materials quickly please contact us - we will do our best to help you source materials needed.

We do not deliver on weekends and bank holidays. Sometimes we can deliver on Saturdays - please check with us before placing the order.
If you need any further information please contact us tel. 02081910776

We can help to calculate price per m2 or linear meter (one meter in length) cost, please just contact us via phone 02081910776, email or live chat. Alternatively, you can work it out yourself quickly and easily: to get cost per meter square please divide price shown in orange area by ''Required area (m2)'' Example price of £28.80 divided by board coverage 2.88m2 = cost of £10.00 per m2.

INSTALLERS

No matter whether you choose a local installer or a national company, there’s a few tips to help you find the right installer for your home insulation improvements, such as asking for recommendations and making sure that they’re part of a certification scheme. This makes sure that they have the right skills and standards of workmanship to carry out the installation, and you can be sure that they know exactly what they are doing.

4 TIPS FOR CHOOSING THE BEST INSULATION INSTALLER

1. Thermal inspection picture in portfolio

It’s worth seeing a installer’s previous work. There’s no harm asking if you can see any properties nearby that they’ve installed insulation in. Best way would be to see Infrared Thermal Imaging Inspections. Thermal cameras spot small, but key changes in temperature in different areas of a house, identifying problematic areas that the human eye never could and some that a visual inspection could only hypothesize.

2. Reviews

Along with checking recommendations and previous work, finding reviews online can often be a great way to find out if they provide a good service or not. However, it’s best not to solely rely on reviews you may find or review websites, as there’s no controlling who writes them.

3. Compare prices

Comparing prices will also ensure companies can’t take advantage of you and give you a fair price. 

4. Word of Mouth

The best way to find a great insulation installer is through recommendations. Make sure you ask friends and family. They will most likely give you their honest opinion and can tell you from first hand experience.

 

Whether you require a wall, cladding, external wall, loft or floor insulation fitted, you can find and hire your local insulation installers from popular UK web pages. A simple internet search will return thousands of potential installers near your area.

 

https://www.nia-uk.org/find-an-installer/

https://www.checkatrade.com/

https://www.mybuilder.com/

https://www.ratedpeople.com/local-thermal-insulation

 

STOCKIST

We are the stockist of construction materials and related products for both trade and DIY from most recognizable brands in the UK like Cordek, RCM, Promat, Rockwool, Isover, Celotex, Xtratherm, Ursa, Low-E, Cedral, Kingspan, Dufaylite, British Gypsum, K-rend, Ecotherm, Iko enertherm, Kay-Metzeler, Terrawool to allow you to complete your insulation job on time at competitive prices and the highest standards.

 

Whether you are a large company or a DIYer, if you need a large amount of insulation materials, we can offer quantity discounts at the best prices. Please contact us and our friendly customer service will try to find the best and cheapest solutions for you. We value your time and we will try to deliver the products as soon as possible at a reasonable price to your construction site or house. The UK's leading insulation supplier near you and your needs. Price List available upon request.
30-50mm Unilin TR/MG Tapered Roof Insulation (pack of 6)
30-50mm Unilin TR/MG Tapered Roof Insulation (pack of 6)
£ 294.35