92.5mm Safe-R SR/TB-MF Thermal Liner Mech-Fix Insulated Plasterboard is a combination of premium phenolic foam insulation core with a composite foil facing bonded to 12.5mm tapered edge plasterboard for dry lining internal walls, sloped roofs and ceilings.

Safe-R Xtratherm SR/TB-MF Thermal Liner range is a high-efficiency thermal insulation with a certified thermal conductivity (lambda value) as low as 0.020W/mK.

SR/TB-MF is an easy to install and decorate 3 in 1 solution which provides high-levels of insulation, dry-lining and vapour control layer in one easily applicable 2400 x 1200 x 92.5mm superior insulated plasterboard.

Safe-R Xtratherm SR/TB-MF 'Mech Fix' is suitable for new build and refurbishment projects to save money by reducing the heat loss from buildings.

The composite facings on both sides of the SR/TB-MF thermal liner board incorporate an integral vapour barrier, which helps to reduce the risk of condensation.

Xtratherm products are stable, rot proof and will remain effective for the life span of the building (depending on specification and installation). 

Care should be taken to avoid contact with acids, petrol, alkalis and mineral oil, when contact is made, clean materials in a safe manner before installation. 

Ensure tight fitting of the insulation boards to achieve continuity of insulation as asked for within the ACDs.

The insulation boards can be readily cut using a sharp knife or fine toothed saw.

When it comes to health and safety, Xtratherm boards are chemically inert and safe to use.

Xtratherm Safe-R SR/TB-MF Thermal Laminate is only suitable for mechanically fixed applications.

Specification:

Width: 1200mm

Length: 2400mm

Pack Quantity: 4

Pack Coverage: 11.52m2

R-Value: 3.85m2K/W

Thermal Conductivity: 0.020W/mK

Compressive Strength: >120 (kPa)

Reaction to Fire: Euroclass B-s1, d0

Key points:

 · Three-in-one solution.

 · Integral vapour control layer.

 · Reduced insulation thickness.

 · Mechanical fix applications.

 · Highly responsive insulation system.

 · High levels of insulation and drylining in one fix.

 · Euroclass B-s1 d0 fire classification.

 · Suitable for newbuild, retrofit and refurbishment.

 · Thermal conductivity (lambda value) of 0.020 W/mK.

 · Suitable for drylining internal walls, sloped roofs and ceilings.

 · Standard size 2400mm x 1200mm (8 x 4) boards.

 · Superior performance phenolic insulation.

 · Insulation, drylining and vapour barrier in one board.

 · Easy to handle and install.

Integral vapour control layer:

 · The composite glass tissue facing on SR/TB-MF provides a gas and vapour tight barrier, reducing the condensation risk. 

 · A continuous vapour control layer is created when the Xtratherm Safe-R SR/TB-MF joints are sealed and taped in accordance with drylining good practice. 

 · Thanks to its low emissivity foil facings SR/TB-MF, facing into an unventilated air void between battens, will improve the U-Value of the wall.

Handling, Cutting and Storage:

 · Xtratherm insulation should be stored off the ground, on a clean flat surface and must be stored under cover. 

 · The polythene wrapping is not considered adequate protection for outside exposure. 

 · Care should be taken to protect the insulation in storage and during the build process.

 · Appropriate PPE should be worn when handling insulation.

Certification:

 · BBA Certification No.10/4803.

 · BS EN ISO 9001 Quality Management System.

 · BS EN ISO 14001 Environmental Management System.

 · Standard - BS EN 13166.

*Further information may be found in our Downloads section.

Fairly easy access to all PDF files.

Datasheet ǀ Declaration of Performance - DoP ǀ BBA Certificate ǀ Installation Guide ǀ Certificates ǀ Brochure ǀ SPEC Sheet 

*Special Product - Non returnable cancelable.