34.5mm (25mm) Unilin XT/TL Thin-R PIR Insulated Plasterboard is made of 25mm PIR insulation bonded to 9.5mm plasterboard used for internal walls, ceilings, pitched and flat roof applications.

Unilin XT/TL Insulation and Drylining Board provides an effective vapour control layer and is suitable for a variety of wall types for both refurbishment and new build projects.

XT/TL Insulated Plasterboard is designed to save money and time by reducing the heat loss from buildings in pitched roof, flat roof and wall applications.

The composite kraft facing on both sides of the Unilin XT/TL thermal laminate incorporates an integral vapour barrier, which helps to reduce the risk of condensation.

Thermal Liner Dot and Dab XT/TL improves energy efficiency of your home by reducing energy costs and improving living conditions.

Unilin XT/TL Insulated Plasterboard can be used as a cheaper alternative to Celotex PL4000, EcoTherm Laminate, Gyproc Thermaline and Knauf Laminates.

This insulated plasterboard can be readily cut using a sharp knife or fine toothed saw.

Appropriate PPE should be worn when handling Unilin XT/TL Insulated Plasterboard.

The thermal conductivity (lambda value) of PIR rigid insulation foam core is 0.022W/mK.

The thermal conductivity (lambda value) of plasterboard is 0.17W/mK.

Specification:

Thickness: 34.5mm

Length: 2400mm

Width: 1200mm

Board coverage: 2.88m2

R-Value: 1.20 m2K/W

Thermal Conductivity: 0.022 W/mk

Density (Foam Core): 30-32 Kg/m3

Compressive Strength: >150 kPa

Water Vapour Resistivity: >100 MNs/gm

Reaction to Fire: Euroclass B s1 d0

Unilin XT/TL Thin-R PIR Insulated Plasterboard Features:

 · Saves money and time.

 · Incorporates an integral vapour barrier.

 · Helps to reduce the risk of condensation.

 · Reduced insulation thickness.

 · Reduce the risk of condensation.

 · Suitable for a variety of wall types.

 · Cost effective 3 in 1 solution.

 · Suitable for refurbishment and new build.

 · Easy to install and decorate.

 · Effective thermal insulation and drylining.

 · Insulation and drylining in one easy applicable board.

 · Provides an effective Vapour Control Layer (VCL).

 · Cheaper alternative to Celotex PL4000, EcoTherm Laminate, Gyproc Thermaline and Knauf Laminates.

 · Thermal conductivity (PIR core lambda) 0.022 W/mK.

Unilin XT/TL PIR Insulated Plasterboard Installation Guidelines:

 · Ensure the wall is dry and free from any protrusions / wall paper etc.

 · Mark the position of Unilin XT/TL Insulated Plasterboard on the wall.

 · Setting out and planning board positioning is essential.

 · Apply adhesive dabs to the wall in accordance with BS8212.

 · Ensure a 50mm continuous ribbon of adhesive is created at the top and bottom of each board and around all openings.

 · Follow adhesive manufacturer’s guidelines.

 · General recommendation is to apply vertical dabs at 300mm centres, 25mm in from the edge.

 · Dabs should be 50-75mm wide and approximately 25mm deep to allow for tamping.

 · Total contact with the board area should be minimum 20%.

 · Maximum height installation for this system is 3000mm.

 · Lift the Unilin XT/TL Insulated Plasterboard into position using wedges on the floor.

 · Align Insulated Plasterboard squarely on wall.

 · Apply pressure to the board to level and embed it into the adhesive.

 · Allow a 15mm expansion joint at the top and bottom of the panel, and fill with foam filler.

 · Insulation should be cut back to accommodate an adjoining panel at external corners.

 · Joints should be tightly butted.

 · When the adhesive has dried, 3 mechanical fixings (thermally broken) should be fixed through the centre of the board.

 · Seal and tape the joints of Unilin XT/TL Insulated Plasterboard to ensure a continuous vapour control layer is created.

 · Plaster skim Unilin XT/TL Insulated Plasterboard to finish.

 · When upgrading existing properties, a professional should be engaged to assess the property for appropriate insulation treatments and effective detailing.

 · Walls should be dry and decoration stripped back to the wall substrate.

 · Appropriate ventilation strategies must be considered as part of the overall energy upgrade.

*Further information may be found in our Downloads section.

Fairly easy access to all PDF files.

Datasheet ǀ Declaration of Performance - DoP ǀ BBA Certificate ǀ Installation Guide ǀ Certificates ǀ Brochure ǀ SPEC Sheets

*Special Product - Non returnable cancelable.