3mm Isocheck Re-Mat 3T for Tile Finish is an impact acoustic resilient mat designed to reduce impact sound transmission through concrete floor decks and all types of floor finishes.

Isocheck Re-Mat 3T (1000mm x 20000mm) consists of a 3mm layer of matting constructed from waste rubber and cork mixed with a polymer binder to form a resilient mat.

Re-Mat 3T is suitable for all types of floor finishes including ceramic tiles, stone, marble, vinyl, carpet and solid or laminate wood.

Laboratory performance achieved for Re-Mat 3 is 17dB ΔLw and 18dB ΔLw when used beneath a tiled floor.

Treated floor can meet with the Robust Detail options A & B within E-FC-8, when used in conjunction with isopoli 5mm under screed layer.

A heated floor system can also be installed beneath Re-Mat 3 acoustic and soundproofing matting.

Also available is Re-Mat 3T and Re-Mat 5T - a 3mm or 5mm layer suitable for a tile finish.

Re-Mat 3T system is a specially designed acoustic floor solution that could complement the requirement for underfloor heating.

Specification:

Thickness: 3mm

Width: 1000mm

Length: 20000mm

Size: 3mm x 1000mm x 20000mm

Profile: Underlay Roll

Material: Cork and Rubber

Colour: Black and Beige

Weight: 19.72kg

Weight per m2: 1.05kg

Tensile strength: >500kPa

Density: 700kg/m3 

Compression: 15%

Operating temperature range: -30˚ to 90˚

3mm Isocheck Re-Mat 3T for Tile Finish Features:

 · Reduce impact sound.

 · Acoustic resilient mat.

 · Only 3mm layer of matting.

 · 17dB impact improvement system.

 · Used on concrete and timber floors.

 · Suitable for all types of floor finishes.

 · Made of cork and waste rubber mixed with a polymer binder.

 · Used in new build, refurbishments and conversion projects.

 · A heated floor system can also be installed beneath the Re-Mat 3T.

 · Can meet with the Robust Detail options A & B within E-FC-8.

 · Suitable for ceramic tiles, stone, marble, vinyl, carpet and solid or laminate wood.

3mm Isocheck Re-Mat 3T Resilient Mat for Tile Finish Installation Guidelines:

 · Ensure Isocheck Re-Mat is stored in a dry, ventilated area.

 · The floor surface should be swept free of all wax, oil, grease, grit, loose debris and other objects that could damage the Isocheck Re-Mat systems.

 · Fill holes and irregular surfaces with levelling compound.

 · Unroll Re-Mat and allow it to rest for 24 hours to allow the material to acclimatise before measuring and cutting.

 · Cut using a sharp knife and a straight edge.

 · Lift Re-Mat and evenly apply adhesive with a triangular-notched trowel.

 · Leave for approximately 20 minutes or until the adhesive is tacky before laying the Isocheck Re-Mat.

 · Leave a 2mm minimum gap between the edge of the Re-Mat and the wall or skirting.

 · Tightly butt-joint rolls of Re-Mat.

 · Smooth out the surface of the Re-Mat with a roller, pressing down firmly to remove any air bubbles and to ensure the Re-Mat is correctly adhered.

 · DO NOT mechanically fix Re-Mat.

 · Fill the gap beneath the plasterboard and the screed with flexible sealant.

 · Fit the timber, ceramic, stone or soft floor finish leaving a 5mm gap between the perimeter and the wall.

 · If fitting ceramic or stone tiles use a water-resistant grout and seal gap between the skirting and the tiles.

 · If fitting soft coverings such as carpet, the gripper rods can be fixed through the Re-Mat at the perimeter.

 · If in doubt in any area, please call Isomass prior to commencement of work.

*Further information may be found in our Downloads section.

Fairly easy access to all PDF files.

Datasheet ǀ Declaration of Performance - DoP ǀ BBA Certificate ǀ Installation Guide ǀ Certificates ǀ Brochure ǀ SPEC Sheet 

*Special Product - Non returnable cancelable.