Largely manufactured from recycled glass (e.g. windscreens) and mineral base materials such as sand and without the use of binding agents. The ingredients are melted into molten glass, which is cooled and crushed into a fine powder. The powdered glass is poured into molds and heated (below the melting point) in a "sintering" process that causes the particles to adhere to one another. Next, a small amount of finely ground carbon-black is added and the material is heated in a "cellulation" process. Here, the carbon reacts with oxygen, creating carbon dioxide, which creates the insulating bubbles in the (material). CO2 accounts for more than 99% of the gas in the cellular spaces.
Cellulose insulation is a material made from recycled newspaper. The paper is shredded and inorganic salts, such as boric acid, are added for resistance to fire, mould, insects and vermin. The insulation is installed either blown or damp-sprayed depending on application.
Wood fibre
The success of wood fibre insulation derives from an attractive environmental profile combined with a whole bag of functions including rigid insulation, sheathing and sarking for timber frames, roofs and flooring as well as flexible insulation for studs and rafters.
Wood of course is renewable, it sequesters carbon during its growth and product production is relatively free from pollution. The insulation value of wood fibre boards is not as dimensionally efficient as some of the orthodox petro-chemical materials - but it's no slouch either - typically coming in with a 'k value' range of between 0.038-0.043 W/mK depending on format.
Hemp
Hemp fibres are produced from hemp straw of the hemp plant. Most hemp is imported, but an increasing amount of home-grown crop is becoming available. Hemp grows up to a height of nearly 4 metres within a period of 100-120 days. Because the plants shade the soil, no chemical protection or toxic additives are required for hemp cultivation. The product is composed of, usually, 85% hemp fibre with the ballance made up of polyester binding and 3-5% soda added for fire proofing.
Straw
Straw is an agricultural by-product, the dry stalks of cereal plants, after the grain and chaff have been removed. Straw makes up about half of the yield of cereal crops such asbarley, oats, rice, rye and wheat.
External Wall Insulation, commonly known as EWI or K-Rend, is a comprehensive multilayer insulation system affixed to an existing wall, comprised of various layers such as a insulation, base coat, reinforced mesh, and finishing coat, aimed at enhancing home energy efficiency and preventing water infiltration, thus maintaining the masonry pleasantly dry. External wall insulation is one of three potential ways to insulate the walls of your home, the other options being cavity wall insulation and internal insulation. The effect of external insulation is to warm the wall by separating from cold temperature.
It has been proven by German specialists that in order to improve the insulating properties of the building, insulation must be fitted on the exterior of the walls. By doing so the dew point is simply moved away from the wall.
Therefore this installation process involves fixing a layer of insulation material to the external walls of a property, and covering it with reinforcement and a special render in a range of decorative finishes.
As with stone walls, the external insulation can be glued and then mechanically fixed to the wall. This method is often required for insulating walls on solid wall properties where there's no option for cavity wall insulation. The external insulation cost is usually higher than internal wall insulation. On top of that, there will be a cost involved in erecting scaffolding and removing all of the pipes that are fixed to the masonry wall. Even with the higher cost, the advantages external insulation offers over internal mean that it is difficult to disregard. However, EWI and render systems take a fair amount of work to install, and essential to the process is having good tools for the job. It will also change the external appearance of the house. In most cases that will mean gaining planning permission before undertaking the work, so you do need to check with local authority from the outset.
Under Building Regulations, if 25% or more of a wall is to be insulated externally, it is typically necessary to bring the entire wall up to current standards. The thermal performance of the insulated wall must have a U-value of no more than 0.30W/m²K. When it comes to using external wall insulation to insulate a solid wall, you'll be looking at the following U-value figures:
External insulation will add physically thickness to the wall, most evident at the reveals and eaves. You will have to extend your existing window sill using either uPVC or Aluminium window sill extender. In addition, it is usually impractical to return the insulation into the window and door reveals.
There are thin insulation options, like 10mm grey polystyrene that can be used on a reveal to help overcome this challenge.
Installing EWI doesn’t disrupt things inside your property in the way that internal insulation would, so you can easily live in the house during the work. You can expect some noise while walls are being prepared and the insulation is fixed. But disruption should be minimal. EWI can also help to improve weatherproofing and sound resistance. For instance, Rockwool DD sound slab has been specifically developed for use in external wall insulation systems where a higher density slab is required. The structure of the fibres in Rockwool Sound Slab make them ideal for use as a sound absorber. Rockwool Sound Slab works in two distinct ways to reduce noise, either by impeding the transmission of sound through an element of the structure, or by absorption of sound at the surface.
Adding external wall insulation is also a good opportunity to update the appearance of your home. You could make it look pretty much identical to how it was previously or make some improvements to boost your house appearance, possibly even increasing its value. External wall insulation is an invisible part of your home that you won’t be able to see once in place. That is why it is often called fit-and-forget solution.
EWI INSTALLATION
The first step before beginning the EWI installation process is to do a render test. This will identify whether your existing render is strong enough to support the particular insulation. Second step would be removing an existing pipework from the building so the installation process can begin. On this stage you should also fit a protective layer over your windows, which will prevent them from being damaged during the installation process. External wall insulation does not normally reach the ground but instead begins a few inches above.
Once you’ve decided on the height, this is where the aluminium start track or base track, will be installed. Starter tracks should be installed against a flat surface, with any gaps filled with expanding foam, plastic trims, or silicone sealant, however it would be preferred to dub out the wall locally to ensure full contact with the wall and rear up stand of the trim. Trims are usually set 200mm above ground level to reduce the effects of ‘splash back’ of rainwater, dirt and other contaminants, however it is advised that DPCs should not be bridged.
Once the starter track has been installed, the application of the insulation boards onto the wall can begin. Insulation boards should be laid in a staggered pattern, and should be staggered at the edges of buildings so that they form a toothed finish. Generally boards should be cut in an L shape around the corners of openings, and small cuts of boards should not be allowed. It would be best practice to limit cuts to a minimum of 200mm. Gaps in boards should be limited, and should be filled with expanding foam. Boards should be level so that the basecoat and decorative finish are installed on a flat true surface. Leveling of boards can be undertaken with adhesive renders or dubbing out renders, and should be assessed at contract stage and allowed for within the contract costs. Adhesive renders should be applied to the rear of the board, and should follow either a dot and dab method, with renders to the board edges, or a fully applied adhesive using a serrated trowel.
As well as the adhesive, mechanical fixings are also used to secure the insulation boards. Around 8 – 10 fixings are hammered in per square metre, to ensure the insulation boards will not get blown off or fall off during periods of bad weather.
Next step would be to add corner beds to the corner surfaces. Corner beads and stop beads are a great way to ensure the insulation remains secure and tight around windows and doors.
Once the boards and beading have all been installed, two layers of render with strengthening properties are applied, with a fibreglass mesh sitting between the two layers of render. Meshes should overlap by a minimum of 100mm at all edges and should overlap with integral meshes on the corner beads and starter track clips. Check with the system supplier as laps can reduce to 75mm if agreed. Stress patches should be installed to all corners at openings and should be sized by the system designer. Base coat application should only be carried out when the weather is fine and free from rain. It is recommended to carry out a daily check on the weather forecast, for a minimum of 48 hours prior to the proposed application of system designers.
Polypropylene or glass fibre meshes should be installed into the wet basecoat, using the back of a steel trowel and pushed in, so that they sit in the top third. This ensures strength and continuity of the basecoat. A second basecoat is then applied, and there should be no visual sign of the mesh once this is applied. Once the basecoat has been applied, it should be left to cure in its appropriate state to receive the priming paint and then final finish i.e. suitably scarified in the case of thick coat finishes or sponged for fine textures.
The final coat of render can now be applied. This render is the last coating in the installation process, meaning that it is important to choose the exact colour and texture you like, as it will be in view on the outside of the building.
EWI SYSTEM COMPONENTS
INSULATION LAYER
This is the main insulation normally made of either expanding polystyrene or mineral wool. Technologies such as phenolic resin insulation are also available. All of these materials are used to prevent heat escaping through walls. The insulation forms the main thermal layer as well as being the background for applying the basecoat and finishes to. Boards are fixed either directly with adhesive, with mechanical anchors, or a combination of both.
The spider diagrams below are an extract from a recent multi-criteria comparison of insulation materials carried out for EUMEPS (European Manufacturers of EPS). These are taken from the External Wall Insulation comparison and shows EPS having the lowest overall environmental impact.
Picture credit:sundolitt.com/en/Environment/
FIXINGS
Fixings are specified to suit the existing substrate, the height and shape of the building, its location and elevation, and proximity to other buildings. Fixings should be specified by the system designer, and calculations made to check the pull-out value of the specified fixings. All mechanical anchor suppliers will provide printed literature with characteristic pull-out values and these can be used to specify the fixings, however best practice would be to check the site pull-out value and carry out wind and fixing analysis calculations based on these findings against localised conditions. This is the approved method to ensure the correct fixings and quantity are used.
PRIMER
The primer helps waterproof the EWI system and act as a barrier to moisture passing from the outside in. Some primers also have inherent insulation properties adding to the overall efficiency of the system.
GLASS FIBRE MESH
This part is used to hold the basecoat in place whilst it dries. Another layer of primer is then applied over the top of it.
BASECOAT/ BOARD ADHESIVE
Adhesive provides the perfect base for fixing all types of external insulation boards. The adhesive is waterproof, frost proof and vapour permeable, ensuring that your EWI system remains stable and structurally sound for years to come. Adhesive renders should be applied to the rear of the board, and should follow either a dot and dab method, with renders to the board edges, or a fully applied adhesive using a serrated trowel.
RENDER FINISH
This is the final layer of EWI and has a decorative function, enhancing the look of your home. There are various different renders available. Silicone Render is a flagship silicone-based thin coat render. Renowned for being long lasting and aesthetically pleasing, this render is the classic choice for homeowners and businesses alike. With hydrophobic properties, the Silicone Render has self-cleaning capabilities and also increased resistance to biological growth. It’s a customer favourite because once it’s installed it requires minimal upkeep and continues to look fantastic.
Silicone Silicate Render is the most popular hybrid silicone render, offering great performance and great value. Silicone Silicate is fantastically versatile, providing the key benefits of a thin coat render with the added boost of self-cleaning and breathability that the silicone technology provides. Silicone Silicate is perfect for a standard classic finish that will maintain its brilliance in the long term.
Acrylic Render is the best value render. It is impact resistant and is most well known when it comes to coloured render as it retains the colour pigment even after extended exposure to UV. Acrylic Render achieves a vibrant, stand out finish.
Brick Slip Sample (Blackpool) Decorative Wall Cladding is a thin slice of brick slip tile 71mm x 240mm in Blackpool (Anthracite) colour that allows you to get a feel how Blackpool brick slips will look on your interior or exterior walls.
Elastolith Brick Tiles Blackpool are flexible acrylic brick..
Brick Slip Corners Colour Blackpool (2 linear metres) referred to as 'pistols' are L-shaped brick slips to fit around external corners of your walls to create an authentic impression of a solid brick wall.
The brick slips corners are very lightweight and incredibly easy to install, making them pe..
Corner Brick Slips Elastolith Colour Blackpool
Flexible, Frost-proof (Box of 24 corner brick slips)
Brick Slip Colour Blackpool-Anthracite (1m² - 48 brick slips tiles per box) is an acrylic, frost-proof and vapor-permeable thin slice of brick slip tile that creates a natural and authentic look of brickwork to your walls.
The brick slips are very lightweight and incredibly easy to install, makin..
Brick Slips Elastolith 1m2 (Colour Blackpool)
Flexible, Frost-proof (Box of 48 brick slip tiles)
EWI-075 Silicone Render 3mm grain is a weatherproof and frost-proof silicone thin-coat render used as a protective and decorative finish to an External Wall Insulation (EWI) system that can be applied by hand using a trowel straight out of the bucket.
Silicone Render EWI Pro EWI-075 25kg is a pol..
Full End Caps to fit Type 761 Aluminium Over Sill Extender is a pair of aluminium push fit full end caps to fit the type 761 range of window over sill extensions / extenders.
The WEC761 end caps pair (left and right handed) is a non-corrosive aluminium profile powder coated white on both sides.
..
Full End Caps Pair to suit Sill Type 761
Push fit end caps to fit the type 761 range of window sills
To suit WEC761 flashing and window sill extensions
Left and right handed end caps powder coated white
Thin coat rendering and most conditions requiring the weathering
Corn Primer TC15 is a low odour, ready to use priming paint which is quick and easy to apply by brush, roller or spray.
It is available in a wide range of colours which are co-ordinated to the colour of the Silicone TC 15 topcoat.
Primer TC should be used after the application of Base Coat (..
Coverage approx. 50-60m2 per bucket
Ready to use - supplied in 15kg tubs
Application temperature should be a minimum of 5°C
Surface must be protected from rain and drying too fast
Do not apply in conditions of strong sunshine or wind
Cream K-Rend Silicone K1 Monocouche Scratch Render is a breathable polymer modified silicone-cement based self-coloured render designed for most spray machines and hand application within External Wall Insulation systems.
Monocouche Silicone K1 is specifically designed to incorporate the benefits..
Corn K Rend Silicone TC 15 is an organic resin render incorporating a silicone resin emulsion and an acrylic resin dispersion in a ready to use render.
If applied according to the manufacturer’s instructions it can be used on a variety of prepared exterior surfaces to provide an attractive, low ..
Coverage approx. 10m2 per 25kg bucket
Ready to use - supplied in 25kg buckets
Do not apply onto damp or frozen substrates
Application temperature should be a minimum of 5°C
Do not apply in conditions of strong sunshine or wind
70mm Kingspan K5 Kooltherm Phenolic Insulation Board is an external wall insulation board for masonry walls with a fibre-free rigid thermoset phenolic core used for external wall insulation (EWI) and dry cladding insulation systems.
Kooltherm K5 External Wall Board 70mm x 600mm x 1200mm is an ins..
70mm Kingspan K5 Kooltherm Insulation Board
Thermal Conductivity as low as 0.021W/mK
Reaction to Fire Euroclass C-s2,d0 (Fire Rating)
Resistant to the passage of Water Vapour
External Wall Insulation (EWI) and dry cladding systems
100mm Kingspan K-Roc® Rainscreen Façade Insulation Slab is a high-performance class A1 rock mineral fibre insulation slab designed for use behind rainscreen façades in all buildings regardless of building type, height, construction and location.
Rainscreen Façade Insulation Slab Kingspan K-Roc 10..
Silicone Adhesive and Sealant (Anthracite) CT1 – 290ml cartridge is a ready-to-use silicone based sealant and adhesive that can be used to seal: solid wall insulation, render-only systems, baths, showers, roofs, doors, windows, and gutters.
Anthracite colour silicone sealant and adhesive is an ea..
100mm Grind in Verge Trim Aluminium Profile Type 781 is an unique flashing profile manufactured in 1.2mm pre-coated white aluminium in 2500mm long lengths.
Grind in Verge Trim is designed to improve visual appearance of the building and to help prevent the water blowing up and soaking behind the ..
100mm Grind in Verge Trim Aluminium Flashing Profile Type 781 - 2500mm long
Grind in verge trim manufactured in 1.2mm pre-coated white aluminium profile
Can be fitted with a low-expansion foam or a weatherproof silicone sealant
Grind In Trim Flashing is suitable for newbuild, retrofit and refurbishment projects
Suitable for external wall insulation systems, thin-coat rendering and weathering
100mm Aluminium Oversill and Window Sill Extension (O'sill Extender 751) is a non-corrosive aluminium ledge trim suitable for EWI (external wall insulation) systems, thin-coat rendering and most conditions requiring the weathering.
WEC751 Window Sill Extender 100mm is a 2500mm long profile made f..
100mm Aluminium Verge Profile Type 771 is a flashing over-trim profile manufactured in 1.2mm pre-coated white aluminium in 2500mm long lengths.
It can be fitted either with a low-expansion foam or a weatherproof silicone sealant to meet the recommendations of insulation systems manufacturers.
..
100mm Aluminium Verge Over Trim Profile Type 771 in 2500mm lengths
Universal flashing over-trim profile manufactured in 1.2mm pre-coated white
Can be fitted with a low-expansion foam or a weatherproof silicone sealant
Over Trim Flashing is suitable for newbuild, retrofit and refurbishment projects
Suitable for external wall insulation systems, thin-coat rendering and weathering
100mm CTP Wood Fixings for Timber Frame is a high-quality polypropelene head and steel nail fixing designed to secure insulation panels such as EPS (expanded polystyrene) or phenolic Kingspan K5.
Friulsider CTP Timber structure insulation panel fixings are suitable for rigid and semi-rigid insula..
100mm Grey EPS for External Wall Insulation (Graphite Expanded Polystyrene) is an insulating material with about 20-25% better thermal insulation properties than basic white EPS that can effectively reduce heating costs and improve the appearance of the building.
Complete external wall insulation..
External Wall Insulation Systems
Lightweight - Cost efficient - Durable
High Resistance to Mold Growth
Thermal Conductivity: 0.031W/mK
Easily cut with a sharp knife to any size and shape
100mm Aluminium Upstand Verge Trim Type 791 is suitable for external wall insulation systems, thin-coat rendering, waterproofing and most conditions requiring the weathering.
Verge Trim with Upstand has an up-stand that can be pushed under a barge board designed to reduces the need for a mastic s..
100mm Verge Trim Aluminium Flashing Profile with Upstand Section Type 791
Manufactured in 1.2mm pre-coated white aluminium in 2500m long lengths
Can be fitted with a low-expansion foam or a weatherproof silicone mastic sealant
Verge Trim Upstand Profile is suitable for newbuild, retrofit and refurbishment projects
For external wall insulation systems, thin-coat rendering, waterproofing and weathering
110mm Rockwool DD External Wall Dual Density Slab is a façade thermal and acoustic insulation slab developed for insulated render systems in new build and refurbishment projects to prevent the spread of fire.
Rockwool DD is a high-performance, non-combustible stone wool slab used to insulate the ..
120mm Kingspan K-Roc Rainscreen Rock Mineral Fibre Insulation Slab achieves European Classification (Euroclass) A1 and so can be used behind rainscreen façades in all buildings regardless of building type, height, construction and location.
Rainscreen Façade Insulation Slab Kingspan K-Roc 120mm i..
120mm Self Drilling Screw Rawlplug R-WX-T (box of 200 screws) is an anti-corrosive coated screw designed to anchor insulation to sheathing boards (e.g. render carrier boards) when used in conjunction with the appropriate fixing washers.
The appropriate washer for 120mm Self Drilling Screws is the..
13-15mm White Movement Bead and Expansion Joint Profile is a smart PVC trim designed to protect the render from cracking and to allow the top-coat to expand and contract in changing weather conditions and the building movements over the years.
PVC Movement beading and expansion joint profile can ..
13-15mm White Render Stop Bead 2500mm is a versatile PVC profile designed to provide a straight clean finish on the edges of plaster and render at doors or windows openings within a thin coat rendering or composite external wall insulation (EWI) systems.
This quick and easy to install plastic sto..
13-22mm Ivory (Magnolia) External Bellcast Bead with Drip for Rendering is a strong PVC profile designed to protect the render against impact damage and water penetration in external wall insulation (EWI) systems.
EWI Bellcast beads with drip nose are designed to provide a stop to the render abov..
Evolution Long Length Self Drilling Insulation Screw 160mm (Box of 200 screws) is self tapping thread screw used for fixing rigid insulation boards to metal framing typically in conjunction with insulation washers.
160mm Screws are also suitable for fixing insulation to light gauge steel or timbe..
180mm Insulation Panel Fixings LMX10 (Metal Pin Hammer Fix Anchors) are highly-durable, impact resistant fasteners designed to fix and secure insulation panels to the variety of substrates, used for Rockwool DD slabs, EPS (expanded polystyrene) and Kingspan K5 insulation boards.
The mechanical an..
Impact resistant polypropylene anchor
Zinc coated carbon steel expander pin
Anchor diameter - 10mm
Drill the hole - Mount the anchor - Hammer in the metal pin
180mm ISOfast Insulation Panel Fixings are strong, polypropylene fasteners designed to fix and secure insulation panels to the variety of substrates, used for grey EPS, white EPS (expanded polystyrene) and Kingspan Kooltherm K5 insulation boards.
The mechanical anchors are made from plastic, whic..
Reduce thermal bridging within the system
The plastic core is 10mm in width
Fixings are strong and don’t snap when installed
Fixing used should be 40mm-60mm longer than the thickness of the insulation
Drill the hole - insert the fixings and hammer the palstic pin
195mm Rawlplug Metal Pin Facade Fixing (R-TFIX-8M) box of 200 is an easy to install hammer-in façade fixing with steel nail recommended for External Thermal Insulation Composite Systems (ETICS).
Rawlplug Metal Pin Hammer Fixing 195mm is a versatile fixing offering quick, easy and precise installa..
195mm RAWLPLUG (R-TFIX-8M)
Metal Pin Hammer Fixing (box of 200)
Hammer-in façade fixing with steel nail
Easy installation in all substrates (categories A, B, C, D, E)
External Thermal Insulation Composite Systems (ETICS)
20mm Versapanel Cement Bonded Particle Board Class 0 is a robust cement bonded particle building board offering exceptional strength, mechanical and acoustic performance compared with other exterior gypsum sheathing boards.
Euroform Versapanel A2 20mm is a special SFS sheathing board that can be..
20mm Cement Bonded Particle Board CBPB
Versapanel A2, Class 0 Sheathing Building Board
Can be used in external and internal applications
Versatile Versapanel for residential and public applications
Exceptional strength, mechanical and acoustic performance
215mm Insulation Fixing with Metal Pin is a universal plastic fastener with metal pin used to fix the thermal insulation boards to the wide range of substrates like concrete, brick and other blockwork in an External Wall Insulation (EWI) system.
WKTHERM metal mechanical fixing 215mm is made from ..
215mm Metal Pin Insulation Board Fixings
Metal screw with plastic bodies
Keeps the thermal bridging down to a minimum
Drill the hole, Mount the fastener and Hammer in the metal pin
For substrates: Concrete, Brick and other Blockwork
RAWLPLUG R-TFIX-8S Metal Screw Fixing 215mm (box of 100) is a universal screw-in facade fixing designed for External Thermal Insulation Composite Systems (ETICS) based on Polystyrene (EPS), Mineral wool (MW), Polyurethane (PU) and Light wood wool building boards.
215mm Metal Screw Fixing Rawlplug..
215mm RAWLPLUG (R-TFIX-8S)
Quick and easy installation
Unique sleeve compression zone
Easy installation in all substrates (categories A, B, C, D, E)
External Thermal Insulation Composite Systems (ETICS)
Fire Rated Metal Fixing MLN 230mm x 8mm is a hammer driven façade fixing with high corrosion resistance used for Rainscreen Insulation in Ventilated Cladding Systems to fix and secure insulation slabs and boards.
230mm MLN Fire Rated Fixings are suitable for mineral wool (MW) boards, glass wool, ..
230mm x 8mm Fire Rated Fixing MLN (pack of 50 fixings)
Universal metal façade fixing with high corrosion resistance
For Rainscreen Insulation in Ventilated Cladding Systems
For fixing and securing insulation panels (substrates: A, B, D, E)
250mm Stainless Steel Facade Fire Rated Fixing (pack of 125) is a premium stainless steel Rawlplug facade fixing, recommended for use when fire resistance (F120) is a requirement in external wall insulation (EWI) systems.
Fire Rated Fixing 250mm is used to fix and secure the thermal insulation pa..
60mm Aluminium Base Track is a high-quality resistant to corrosion and atmospheric factors baserail profile designed for external wall insulation systems and thin coat rendering.
Base Bead 60mm is used in EWI systems as a cover for the lower part of the thermal insulation material of Expanded Pol..
60mm Aluminium Vented Base Track TF is a high-quality resistant to corrosion and atmospheric factors ventilated profile designed for external wall insulation systems and thin coat rendering as a cover for the lower part of the 60mm thick thermal insulation boards: Expanded Polystyrene (EPS), Kingspa..
60mm Aluminium Vented Base Track SF is a high quality resistant to corrosion and weather conditions ventilated profile designed for External Wall Insulation (EWI) systems and thin coat rendering.
Ventilated Base Track 60mm is used in insulated render systems as a cover for the lower part of the 6..
70mm Heavy Duty Full System Stop Bead with PVC Drip-Nosing is a perforated full system stop profile designed for External Wall Insulation (EWI) and thin coat rendering made from PPC Galvanised Steel used on the sides of insulated render systems as a cover for the thermal insulation boards: Expanded ..
Stop System - Galvanised Steel - PVC NOSE
FULL SYSTEM HEAVY DUTY STOP BEAD with Nose
Stop Track - Stop Rail - Stop Profile - Drip bead
External Wall Insulation Systems - Full Stop Bead
Provides additional protection against Abrasion and Corrosion
70mm Stainless Steel Full System Stop Bead with PVC Drip-Nosing is a perforated full system stop profile designed for External Wall Insulation (EWI) and thin coat rendering made from resistant to corrosion and staining, low maintenance stainless steel.
The Stop T-Tracks are used on the sides of i..
Stop System - PVC NOSE - STAINLESS STEEL TRACK
SS FULL SYSTEM HEAVY DUTY STOP BEAD with Nose
Stainless Steel: Stop Track - Stop Rail - Stop Profile with nose
External Wall Insulation System - Full Stop Bead Stainless Steel
Provides additional protection against Abrasion and Corrosion
70mm Heavy Duty Base Track PPC is a special starter profile for External Wall Insulation (EWI) systems and thin coat rendering made from polyester powder coated Galvanised Steel which is less expensive than stainless steel.
HD Base Track 70mm is used in insulated render systems as a cover for the..
70mm Galvanised Steel Heavy Duty Base Track with PVC Drip Bead 2500mm is a full system starter profile designed for External Wall Insulation (EWI) and thin coat rendering made from PPC Galvanised Steel.
Full System Starter Profile 70mm is used in insulated render systems as a cover for the lower ..
BASE PROFILE - PPC GALVANISED - PVC NOSE
FULL SYSTEM HEAVY DUTY BASE BEAD with Nose
Base Track - Base Rail - Starter Profile - Drip bead
70mm Heavy Duty Base Track with PVC Nosing-Drip Bead is a professional full system starter profile designed for External Wall Insulation (EWI) and thin coat rendering made from resistant to corrosion and staining, low maintenance stainless steel.
It is used in insulated render systems as a cover ..
Premium Stainless Steel - PVC NOSE
FULL SYSTEM HEAVY DUTY BASE BEAD with Nose
Base Track - Base Rail - Starter Profile - Drip bead
External Wall Insulation Systems - Stainless Steel
Provides additional protection against Abrasion and Corrosion
70mm Stylite Plustherm Grey EPS EWI 70 External Wall Insulation Board is a high performance thermal insulation board manufactured from Expanded Polystyrene (EPS), used in External Wall Insulation (EWI) systems to meet Building Regulations for thermal performance.
Stylite Expanded Polystyrene Insu..
8-10mm Ivory (Magnolia) Angle Bead 2500mm is a special PVC corner bead trim for use on all external and internal rendering and plastering applications where a true, strong and sharp corner is required.
The PVC Angle Bead profile is designed for external corners, around window and door reveals wit..
80mm Aluminium Flexible (Flexi) Slotted Base Track is a resistant to corrosion and atmospheric factors flexi trim designed for curved walls in EWI (external wall insulation) systems and thin coat rendering.
To install a crinkle crankle flexi profile, slit the rear mounting leg and then bend the p..
80mm Window Sill Extension (Oversill and Eaves Flashing Extender) is a non-corrosive aluminium ledge profile suitable for EWI (external wall insulation) systems, thin coat rendering and most conditions requiring the weathering.
WEC721 Sill Extender 80mm is a 2500mm long trim made from 1.2mm thick..
Full End Caps Pair - included
Sill Cover (Type 721)
Material thickness: 1.2mm thick
Length 2.5m - for most EWI External Wall Insulation projects
White Coated on BOTH SIDES, the blue covering is a protection and can be torn off
80mm Aluminium Soffit Eaves Flashing and Window Sill Extension is a non-corrosive aluminium extender trim suitable for external wall insulation (EWI) systems, thin coat rendering and most conditions requiring the weathering.
WEC741 Sill Extender 80mm is a 2500mm long profile made from 1.2mm thick..
Full End Caps Pair - included
Soffit Eaves Flashing (Type 741)
Material thickness: 1.2mm thick
Length 2.5m - EWI External Wall Insulation Systems
White Coated on BOTH SIDES - blue covering protection
80mm Oversill and Window Sill Extension (Universal Metal O'sill) is a non-corrosive aluminium ledge trim suitable for external wall insulation systems, thin-coat rendering and most conditions requiring the weathering.
WEC 761 Standard Sill is a highly-durable 2500mm long profile made from 1.2mm t..
Designed to extend the length of an existing window sill
Over Trim Extension (Type 761)
Material thickness: 1.2mm - O'Sill
Length 2.5m - EWI External Wall Insulation
White Coated on BOTH SIDES - Blue Covering Protection
80mm Stainless Steel Base Track is a top-class resistant to corrosion and staining, low maintenance stainless steel profile designed for external wall insulation systems and thin coat rendering.
Starter Track Stainless Steel 80mm is used in EWI systems as a cover for the lower part of the thermal..
90mm Aluminium Stop Track is a high-quality resistant to corrosion and atmospheric factors stop end trim designed for EWI (external wall insulation) systems and thin coat rendering.
The wall insulation stop end profile is an aluminium plain mill finish box shaped bead designed for various thickne..
90mm Undersill Flashing and Window Sill Extension is a non-corrosive aluminium ledge extender profile suitable for EWI (external wall insulation) systems, thin coat rendering and most conditions requiring the weathering.
WEC731 Sill Extender 90mm is a 2500mm long trim made from 1.2mm thick alumin..
For most conditions requiring the weathering
Sill Cover (Type 731) - Undersill
Material thickness: 1.2mm thick
Length 2.5m - for most EWI External Wall Insulation projects
White Coated on BOTH SIDES - with blue covering protection
Brick Slip Sample (Colorado) Decorative Wall Cladding is a thin slice of brick slip tile 71mm x 240mm in Colorado colour that allows you to get a feel how Colorado brick slips will look on your interior or exterior walls.
Elastolith Brick Tiles Colorado are flexible acrylic brick slips and perfec..
Brick Slip Colour Colorado 1m² (48 brick slips per box) is a high-quality, frost-proof and vapor-permeable thin slice of brick slip tile that creates a natural and authentic look of brickwork to your walls.
The brick slips are very lightweight and incredibly easy to install, making them perfect f..
Brick Slips Elastolith 1m2 (Colour Colorado)
Flexible, Frost-proof (Box of 48 brick slip tiles)
Corner Brick Slips Colour Colorado (brick 'pistols') are L-shaped brick cladding slips designed specifically to fit around external corners of your walls to create an authentic impression of a solid brick wall.
The brick slips corners are very lightweight and incredibly easy to install, making th..
Corner Brick Slips Elastolith Colour Colorado
Flexible, Frost-proof (Box of 24 corner brick slips)
Golden Primer TC15 is a low odour, ready to use priming paint which is quick and easy to apply by brush, roller or spray.
It is available in a wide range of colours which are co-ordinated to the colour of the Silicone TC 15 topcoat.
Primer TC should be used after the application of Base Coat..
Coverage approx. 50-60m2 per bucket
Ready to use - supplied in 15kg tubs
Application temperature should be a minimum of 5°C
Surface must be protected from rain and drying too fast
Do not apply in conditions of strong sunshine or wind
Fintry Stone K-Rend Silicone K1 Monocouche Scratch Render is a breathable polymer modified silicone-cement based self-coloured render designed for most spray machines and hand application within External Wall Insulation systems.
Monocouche Silicone K1 is specifically designed to incorporate the b..
Golden K Rend Silicone TC 15 is an organic resin render incorporating a silicone resin emulsion and an acrylic resin dispersion in a ready to use render.
If applied according to the manufacturer’s instructions it can be used on a variety of prepared exterior surfaces to provide an attractive, lo..
Coverage approx. 10m2 per 25kg bucket
Ready to use - supplied in 25kg buckets
Do not apply onto damp or frozen substrates
Application temperature should be a minimum of 5°C
Do not apply in conditions of strong sunshine or wind
100mm Kingspan GG300 Rigid XPS (Styrozone) is an insulation board used in basements, car parks, inverted roofs and heavy-duty commercial, industrial and cold store flooring insulation projects.
Kingspan GG300 XPS Sheets 100mm x 600mm x 1250mm are resistant to the passage of water vapour, moisture..
100mm Kingspan GreenGuard GG300 R
Rigid XPS Insulation Kingspan Styrozone
Fibre-free rigid extruded polystyrene XPS
Insulation board with high compressive strength (stress)
Basements, car parks, inverted roofs and cold store flooring
10-12mm White Angle Bead 2500mm is a versatile PVC corner bead profile for use on all external and internal rendering and plastering applications where a true, strong and sharp corner is required.
The PVC Angle Bead profile is designed for external corners, around window and door reveals within a..
100mm Aluminium Stop Track is a high-quality resistant to corrosion and atmospheric factors stop end trim designed for EWI (external wall insulation) systems and thin coat rendering.
The wall insulation stop end profile is an aluminium plain mill finish box shaped stop bead designed for various t..
100mm Undersill Flashing and Window Sill Extension is a non-corrosive aluminium ledge extender profile suitable for EWI (external wall insulation) systems, thin coat rendering and most conditions requiring the weathering.
WEC731 Sill Extender 100mm is a 2500mm long trim made from 1.2mm thick alum..
For most conditions requiring the weathering
Sill Cover (Type 731) - Undersill
Material thickness: 1.2mm thick
Length 2.5m - for most EWI External Wall Insulation projects
White Coated on BOTH SIDES - with blue covering protection
110mm Upstand Section Verge Trim Type 791 is used in most conditions requiring the weathering, manufactured in 1.2mm pre-coated white aluminium in 2500mm lengths.
Verge Trim with Upstand has an up-stand that can be pushed under a barge board designed to reduces the need for a mastic seal and remo..
110mm Verge Trim Aluminium Flashing Profile with Upstand Section Type 791
Manufactured in 1.2mm pre-coated white aluminium in 2500m long lengths
Can be fitted with a low-expansion foam or a weatherproof silicone mastic sealant
Verge Trim Upstand Profile is suitable for newbuild, retrofit and refurbishment projects
For external wall insulation systems, thin-coat rendering, waterproofing and weathering
110mm Aluminium Grind in Verge Trim Type 781 is suitable for external wall insulation systems, thin-coat rendering and most conditions requiring the weathering.
Grind in Verge Trim is designed to improve visual appearance of the building and to help prevent the water blowing up and soaking behind..
110mm Grind in Verge Trim Aluminium Flashing Profile Type 781 - 2500mm long
Grind in verge trim manufactured in 1.2mm pre-coated white aluminium profile
Can be fitted with a low-expansion foam or a weatherproof silicone sealant
Grind In Trim Flashing is suitable for newbuild, retrofit and refurbishment projects
Suitable for external wall insulation systems, thin-coat rendering and weathering
110mm Aluminium Oversill and Window Sill Extension (O'sill Extender 751) is a non-corrosive aluminium ledge trim suitable for EWI (external wall insulation) systems, thin-coat rendering and most conditions requiring the weathering.
WEC751 Sill Extender 110mm is a 2500mm long profile made from 1.2..
110mm Over Trim Profile Type 771 is suitable for external wall insulation systems, thin-coat rendering and most conditions requiring the weathering.
It can be fitted either with a low-expansion foam or a weatherproof silicone sealant to meet the recommendations of insulation systems manufacturers..
110mm Aluminium Verge Over Trim Profile Type 771 in 2500mm lengths
Universal flashing over-trim profile manufactured in 1.2mm pre-coated white
Can be fitted with a low-expansion foam or a weatherproof silicone sealant
Over Trim Flashing is suitable for newbuild, retrofit and refurbishment projects
Suitable for external wall insulation systems, thin-coat rendering and weathering
120mm CTP Wood Fixings for Timber Frame is a high-quality polypropelene head and steel nail fixing designed to secure insulation panels such as EPS (expanded polystyrene) or phenolic Kingspan K5.
Friulsider CTP Timber structure insulation panel fixings are suitable for rigid and semi-rigid insula..
120mm Kingspan Green-Guard GG300 XPS is an extruded polystyrene (XPS) insulation board with high compressive for specialist applications such as basements, car parks and inverted roof applications.
Kingspan GG300 XPS Sheets 120mm x 600mm x 1250mm are resistant to the passage of water vapour, mois..
120mm Kingspan GreenGuard GG300 R
Rigid XPS Insulation Kingspan Styrozone
Fibre-free rigid extruded polystyrene XPS
Insulation board with high compressive strength (stress)
Basements, car parks, inverted roofs and cold store flooring
120mm Rockwool DD External Wall Dual Density Slab is a façade thermal and acoustic insulation slab developed for insulated render systems in new build and refurbishment projects to prevent the spread of fire.
Rockwool DD Insulation is a high-performance, non-combustible stone wool slab used to in..
13-15mm Ivory (Magnolia) Movement Bead and Expansion Joint Profile 2500mm is a special PVC trim designed to protect the render from cracking and to allow the top-coat to expand and contract in changing weather conditions and the building movements over the years.
PVC Movement beading and expansio..
13-15mm Ivory (Magnolia) Render Stop Bead is a special PVC profile designed to provide a straight clean finish on the edges of plaster and render at doors or windows openings within a thin coat rendering or composite external wall insulation (EWI) systems.
This quick and easy to install 2500mm pl..
130mm Kingspan K-Roc® Rainscreen Insulation Slab is a non-combustible rock mineral fibre insulation slab, an acceptable solution for use behind rainscreen façades in all buildings regardless of building type, height, construction and location.
Rainscreen Façade Insulation Slab Kingspan K-Roc 130m..
140mm Self Drilling Screw Rawlplug R-WX-T (box of 200) is a special anti-corrosive coated screw designed to anchor insulation to sheathing boards (e.g. render carrier boards) when used in conjunction with the appropriate fixing washers.
The appropriate washer for Self Drilling Screws is the RAWLP..
200mm Insulation Panel Fixings LMX10 (Metal Pin Hammer Fix Anchors) are highly-durable, impact resistant fasteners designed to fix and secure insulation panels to the variety of substrates, used for Rockwool DD slabs, EPS (expanded polystyrene) and Kingspan K5 insulation boards.
The mechanical an..
Impact resistant polypropylene anchor
Zinc coated carbon steel expander pin
Anchor diameter - 10mm
Drill the hole - Mount the anchor - Hammer in the metal pin
200mm ISOfast Insulation Panel Fixings are strong, polypropylene fasteners designed to fix and secure insulation panels to the variety of substrates, used for grey EPS, white EPS (expanded polystyrene) and Kingspan Kooltherm K5 insulation boards.
The mechanical anchors are made from plastic, whic..
Reduce thermal bridging within the system
The plastic core is 10mm in width
Fixings are strong and don’t snap when installed
Fixing used should be 40mm-60mm longer than the thickness of the insulation
Drill the hole - insert the fixings and hammer the palstic pin
215mm Rawlplug (R-TFIX-8M) Metal Pin Facade Hammer Fixing box of 100 is an easy to install hammer-in façade fixing with steel nail recommended for External Thermal Insulation Composite Systems (ETICS).
R-TFIX-8M Rawlplug Metal Pin Hammer Fixing 215mm is a versatile fixing offering quick, easy and..
215mm RAWLPLUG (R-TFIX-8M)
Metal Pin Hammer Fixing (box of 100)
Hammer-in façade fixing with steel nail
Easy installation in all substrates (categories A, B, C, D, E)
External Thermal Insulation Composite Systems (ETICS)
22mm A2 Versapanel Cement Bonded Particle Board is a versatile class 0 building board offering exceptional strength, mechanical and acoustic performance compared with other exterior gypsum sheathing boards.
Euroform Versapanel 22mm is a robust building board that can be used in a wide range of re..
22mm Cement Bonded Particle Board CBPB
Versapanel A2, Class 0 Sheathing Building Board
Can be used in external and internal applications
Versatile Versapanel for residential and public applications
Exceptional strength, mechanical and acoustic performance
RAWLPLUG R-TFIX-8S Metal Screw Fixing 235mm is a screw-in facade fixing designed for External Thermal Insulation Composite Systems (ETICS) based on Polystyrene (EPS), Mineral wool, Polyurethane (PU) and Light wood wool building boards.
235mm Metal Screw Fixing Rawlplug (box of 100) offers quick, ..
235mm RAWLPLUG (R-TFIX-8S)
Quick and easy installation
Unique sleeve compression zone
Easy installation in all substrates (categories A, B, C, D, E)
External Thermal Insulation Composite Systems (ETICS)
295mm Insulation Fixing with Metal Pin is a universal plastic anchor with metal pin used to fix the thermal insulation boards to the wide range of substrates like concrete, brick and other blockwork in an External Wall Insulation (EWI) system.
Metal Pin Screw Fixing 295mm WKTHERM is made from a m..
295mm Metal Pin Insulation Board Fixings
Metal screw with plastic bodies
Keeps the thermal bridging down to a minimum
Drill the hole, Mount the fastener and Hammer in the metal pin
For substrates: Concrete, Brick and other Blockwork
300mm Fire Rated (Fire-Break) Metal Façade Fixing MBA (pack of 125) is an ultimate stainless steel special metal fixing used for Rainscreen Insulation in various Ventilated Cladding Systems.
Rawlplug Fire Rated Fixings are used to fix and secure the thermal insulation panels to a wide range of su..
70mm Aluminium Base Track is a high-quality resistant to corrosion and atmospheric factors baserail profile designed for external wall insulation systems and thin coat rendering.
Base Bead 70mm is used in EWI systems as a cover for the lower part of the thermal insulation material of Expanded Pol..
70mm Aluminium Vented Base Track TF is a high-quality resistant to corrosion and atmospheric factors ventilated profile designed for external wall insulation systems and thin coat rendering as a cover for the lower part of the 70mm thick thermal insulation boards: Expanded Polystyrene (EPS), Kingspa..
70mm Aluminium Vented Base Track SF is a high quality resistant to corrosion and weather conditions ventilated profile designed for External Wall Insulation (EWI) systems and thin coat rendering.
Ventilated Base Track SF 70mm is used in insulated render systems as a cover for the lower part of th..
80mm Heavy Duty Full System Stop Bead with PVC Drip-Nosing is a perforated full system stop profile designed for External Wall Insulation (EWI) and thin coat rendering made from PPC Galvanised Steel used on the sides of insulated render systems as a cover for the thermal insulation boards: Expanded ..
Stop System - Galvanised Steel - PVC NOSE
FULL SYSTEM HEAVY DUTY STOP BEAD with Nose
Stop Track - Stop Rail - Stop Profile - Drip bead
External Wall Insulation Systems - Full Stop Bead
Provides additional protection against Abrasion and Corrosion
80mm Stainless Steel Full System Stop Bead with PVC Drip-Nosing is a perforated full system stop profile designed for External Wall Insulation (EWI) and thin coat rendering made from resistant to corrosion and staining, low maintenance stainless steel.
The Stop T-Tracks are used on the sides of i..
Stop System - PVC NOSE - STAINLESS STEEL TRACK
SS FULL SYSTEM HEAVY DUTY STOP BEAD with Nose
Stainless Steel: Stop Track - Stop Rail - Stop Profile with nose
External Wall Insulation System - Full Stop Bead Stainless Steel
Provides additional protection against Abrasion and Corrosion
80mm Grey EPS EWI 70 External Wall Polystyrene Insulation Board is an easy to install thermal insulation that is compatible with all external wall insulation systems which can be bonded or mechanically fixed to the wall to meet Building Regulations for thermal performance.
Stylite Expanded Polyst..
80mm Heavy Duty Base Track PPC is a special starter profile for External Wall Insulation (EWI) systems and thin coat rendering made from polyester powder coated Galvanised Steel which is less expensive than stainless steel.
HD Base Track 80mm is used in insulated render systems as a cover for the..
80mm Heavy Duty Galvanised Steel Base Track with PVC Drip Bead 2500mm is a full system starter profile designed for External Wall Insulation (EWI) and thin coat rendering made from PPC Galvanised Steel.
Full System Starter Profile 80mm is used in insulated render systems as a cover for the lower ..
BASE PROFILE - PPC GALVANISED - PVC NOSE
FULL SYSTEM HEAVY DUTY BASE BEAD with Nose
Base Track - Base Rail - Starter Profile - Drip bead
80mm Heavy Duty Base Track with PVC Nosing-Drip Bead is a professional full system starter profile designed for External Wall Insulation (EWI) and thin coat rendering made from resistant to corrosion and staining, low maintenance stainless steel.
It is used in insulated render systems as a cover ..
Premium Stainless Steel - PVC NOSE
FULL SYSTEM HEAVY DUTY BASE BEAD with Nose
Base Track - Base Rail - Starter Profile - Drip bead
External Wall Insulation Systems - Stainless Steel
Provides additional protection against Abrasion and Corrosion
90mm Aluminium Flexible (Flexi) Slotted Base Track is a resistant to corrosion and atmospheric factors flexi trim designed for curved walls in EWI (external wall insulation) systems and thin coat rendering.
To install a crinkle crankle flexi profile, slit the rear mounting leg and then bend the p..
90mm Window Sill Extension (Oversill and Eaves Flashing Extender) is a non-corrosive aluminium ledge profile suitable for EWI (external wall insulation) systems, thin coat rendering and most conditions requiring the weathering.
WEC721 Sill Extender 90mm is a 2500mm long trim made from 1.2mm thick..
Full End Caps Pair - included
Sill Cover (Type 721)
Material thickness: 1.2mm thick
Length 2.5m - for most EWI External Wall Insulation projects
White Coated on BOTH SIDES, the blue covering is a protection and can be torn off
90mm Aluminium Soffit Eaves Flashing and Window Sill Extension 741 is a non-corrosive aluminium ledge trim suitable for external wall insulation (EWI) systems, thin coat rendering and most conditions requiring the weathering.
WEC741 Sill Extender 90mm is a 2500mm long profile made from 1.2mm thic..
Full End Caps Pair - included
Soffit Eaves Flashing (Type 741)
Material thickness: 1.2mm thick
Length 2.5m - EWI External Wall Insulation Systems
White Coated on BOTH SIDES - blue covering protection
90mm Oversill and Window Sill Extension (Universal Aluminium O'sill Extender) is a non-corrosive aluminium ledge trim suitable for external wall insulation systems, thin-coat rendering and most conditions requiring the weathering.
Wemico 761 Standard Window Over-Sill Extender 90mm is a highly-dur..
Designed to extend the length of an existing window sill
Over Trim Extension (Type 761)
Material thickness: 1.2mm - O'Sill
Length 2.5m - EWI External Wall Insulation
White Coated on BOTH SIDES - Blue Covering Protection
90mm Stainless Steel Base Track is a top-class resistant to corrosion and staining, low maintenance stainless steel profile designed for external wall insulation systems and thin coat rendering.
Stainless Steel Starter Track 90mm is used in EWI systems as a cover for the lower part of the thermal..
Corner Brick Slips 'pistols' Colour Nebraska (2 linear metres) are flexible mineral-based thin slices of brick corner cladding tiles that creates an authentic look of brickwork on external corners for both internal and external walls.
The brick slips corners are very lightweight and incredibly ea..
Corner Brick Slips Elastolith Colour Nebraska
Flexible, Frost-proof (Box of 24 corner brick slips)
Brick Slip Sample (Nebraska) Decorative Wall Cladding is a thin slice of brick slip tile 71mm x 240mm in Nebraska colour that allows you to get a feel how Nebraska brick slips will look on your interior or exterior walls.
Elastolith Brick Tiles Nebraska are flexible acrylic brick slips and perfec..
Brick Slips for Decorative Exterior Wall Cladding (Colour Nebraska – 1m² per box) are flexible and durable thin slices of brick slip tiles that creates a traditional look of brickwork to your facade walls or interior design.
The brick slips are very lightweight and incredibly easy to install, mak..
Brick Slips Elastolith 1m2 (Colour Nebraska)
Flexible, Frost-proof (Box of 48 brick slip tiles)
Granite Primer TC15 is a low odour, ready to use priming paint which is quick and easy to apply by brush, roller or spray.
It is available in a wide range of colours which are co-ordinated to the colour of the Silicone TC 15 topcoat.
Primer TC should be used after the application of Base Coa..
Coverage approx. 50-60m2 per bucket
Ready to use - supplied in 15kg tubs
Application temperature should be a minimum of 5°C
Surface must be protected from rain and drying too fast
Do not apply in conditions of strong sunshine or wind
Green K-Rend Silicone K1 Monocouche Scratch Render is a breathable polymer modified silicone-cement based self-coloured render designed for most spray machines and hand application within External Wall Insulation systems.
Monocouche Silicone K1 is specifically designed to incorporate the benefits..
Granite K Rend Silicone TC 15 is an organic resin render incorporating a silicone resin emulsion and an acrylic resin dispersion in a ready to use render.
If applied according to the manufacturer’s instructions it can be used on a variety of prepared exterior surfaces to provide an attractive, l..
Coverage approx. 10m2 per 25kg bucket
Ready to use - supplied in 25kg buckets
Do not apply onto damp or frozen substrates
Application temperature should be a minimum of 5°C
Do not apply in conditions of strong sunshine or wind
10-12mm Ivory (Magnolia) Angle Bead 2500mm is a versatile PVC corner bead profile for use on all external and internal rendering and plastering applications where a true, strong and sharp corner is required.
The PVC Angle Bead profile is designed for external corners, around window and door revea..
100mm Aluminium Flexible (Flexi) Slotted Base Track is a resistant to corrosion and atmospheric factors flexi trim designed for curved walls in EWI (external wall insulation) systems and thin coat rendering.
To install a crinkle crankle flexi profile, slit the rear mounting leg and then bend the ..
100mm Window Sill Extension (Oversill and Eaves Flashing Extender) is a non-corrosive aluminium ledge profile suitable for EWI (external wall insulation) systems, thin coat rendering and most conditions requiring the weathering.
WEC721 Sill Extender 100mm is a 2500mm long trim made from 1.2mm thi..
Full End Caps Pair - included
Sill Cover (Type 721)
Material thickness: 1.2mm thick
Length 2.5m - for most EWI External Wall Insulation projects
White Coated on BOTH SIDES, the blue covering is a protection and can be torn off
100mm Aluminium Soffit Eaves Flashing and Window Sill Extension 741 is a non-corrosive aluminium ledge trim suitable for external wall insulation (EWI) systems, thin coat rendering and most conditions requiring the weathering.
WEC741 Sill Extender 100mm is a 2500mm long profile made from 1.2mm th..
Full End Caps Pair - included
Soffit Eaves Flashing (Type 741)
Material thickness: 1.2mm thick
Length 2.5m - EWI External Wall Insulation Systems
White Coated on BOTH SIDES - blue covering protection
100mm Stainless Steel Base Track is a top-class resistant to corrosion and staining, low maintenance stainless steel profile designed for external wall insulation systems and thin coat rendering.
Starter Track Stainless Steel 100mm is used in EWI systems as a cover for the lower part of the therm..
100mm Aluminium Oversill and Window Sill Extension (External Window Sill Extender) is an easy to install non-corrosive profile suitable for external wall insulation systems, rendering and most conditions requiring the weathering.
Universal External Window Sill Extender 100mm is designed to extend..
Designed to extend the length of an existing window sill
Over Trim Extension (Type 761)
Material thickness: 1.2mm - O'Sill
Length 2.5m - EWI External Wall Insulation
White Coated on BOTH SIDES - Blue Covering Protection
110mm Aluminium Stop Track is a high-quality resistant to corrosion and atmospheric factors stop end trim designed for EWI (external wall insulation) systems and thin coat rendering.
The wall insulation stop end profile 110mm is an aluminium plain mill finish box shaped stop bead designed for var..
110mm Undersill Flashing and Window Sill Extension is a non-corrosive aluminium extender profile suitable for EWI (external wall insulation) systems, thin coat rendering and most conditions requiring the weathering.
WEC731 Sill Extender 110mm is a 2500mm long trim made from 1.2mm thick aluminium,..
For most conditions requiring the weathering
Sill Cover (Type 731) - Undersill
Material thickness: 1.2mm thick
Length 2.5m - for most EWI External Wall Insulation projects
White Coated on BOTH SIDES - with blue covering protection
120mm Aluminium Oversill and Window Sill Extension (O'sill Extender 751) is a non-corrosive aluminium ledge trim suitable for EWI (external wall insulation) systems, thin-coat rendering and most conditions requiring the weathering.
WEC751 External Window Sill Extender 120mm is a 2500mm long profi..
120mm Aluminium Verge Over Trim Profile Type 771 is used in most conditions requiring the weathering, manufactured in 1.2mm pre-coated white aluminium.
It can be fitted either with a low-expansion foam or a weatherproof silicone sealant to meet the recommendations of insulation systems manufactur..
120mm Aluminium Verge Over Trim Profile Type 771 in 2500mm lengths
Universal flashing over-trim profile manufactured in 1.2mm pre-coated white
Can be fitted with a low-expansion foam or a weatherproof silicone sealant
Over Trim Flashing is suitable for newbuild, retrofit and refurbishment projects
Suitable for external wall insulation systems, thin-coat rendering and weathering
120mm Aluminium Profile Grind in Verge Trim Type 781 is used in most conditions requiring the weathering, manufactured in 1.2mm pre-coated white aluminium.
Grind in Verge Trim is designed to improve visual appearance of the building and to help prevent the water blowing up and soaking behind the ..
120mm Grind in Verge Trim Aluminium Flashing Profile Type 781 - 2500mm long
Grind in verge trim manufactured in 1.2mm pre-coated white aluminium profile
Can be fitted with a low-expansion foam or a weatherproof silicone sealant
Grind In Trim Flashing is suitable for newbuild, retrofit and refurbishment projects
Suitable for external wall insulation systems, thin-coat rendering and weathering
120mm Verge Trim Aluminium Flashing Profile Type 791 is a verge trim with upstand section manufactured in 1.2mm pre-coated white aluminium in 2500mm long lengths.
Verge Trim with Upstand has an up-stand that can be pushed under a barge board designed to reduces the need for a mastic seal and remo..
120mm Verge Trim Aluminium Flashing Profile with Upstand Section Type 791
Manufactured in 1.2mm pre-coated white aluminium in 2500m long lengths
Can be fitted with a low-expansion foam or a weatherproof silicone mastic sealant
Verge Trim Upstand Profile is suitable for newbuild, retrofit and refurbishment projects
For external wall insulation systems, thin-coat rendering, waterproofing and weathering
15-17mm White Movement Bead and Expansion Joint Profile is a smart PVC trim designed to protect the render from cracking and to allow the top-coat to expand and contract in changing weather conditions and the building movements over the years.
PVC Movement beading and expansion joint profile can ..
15-17mm White Render Stop Bead 2500mm is a versatile PVC profile designed to provide a straight clean finish on the edges of plaster and render at doors or windows openings within a thin coat rendering or composite external wall insulation (EWI) systems.
This quick and easy to install plastic sto..
K-Roc® Rainscreen Façade Insulation Slab Kingspan 150mm is an advanced class A1 rock mineral fibre insulation solution for use behind rainscreen façades in all buildings regardless of building type, height, construction and location.
150mm Rainscreen Slab Kingspan K-Roc is a great heat conductor ..